標題: 單片機制作的電子鐘（含鬧鐘功能）設計 [打印本頁]
作者: 夢想天空    時間: 2017-12-7 08:57
標題: 單片機制作的電子鐘（含鬧鐘功能）設計

文檔下載：
單片機制作的電子鐘（含鬧鐘功能）.pdf (9.4 MB, 下載次數: 53) 多功能的電子鐘.PDF (46.5 KB, 下載次數: 18)

電路圖

程序；

  1. #include<reg52.h>
  2. #include<intrins.h>
  3. unsigned char code displaywelcome[]={" Welcome To My Lcd Timer"};//歡迎界面
  4. unsigned char code displaywish[]={" Happy Every Day ^_^"}; //歡迎界面
  5. unsigned char code overtemperature[]={"OVERTEMPERATURE!"};
  6. unsigned char code digit[]={"0123456789"}; //數字代碼
  7. unsigned char mode,TH,TL,TN,TD,length,tempswitch,Maxtemp=40,amode,alarmmode,minutes,hours,
  8. minutea,seconds,houra=12;
  9. sbit SCLK=P3^6; //DS1302 時鐘輸入
  10. sbit DATE=P3^4; //DS1302 數據輸入
  11. sbit REST=P3^5; //DS1302 復位端口
  12. sbit SET=P1^4; //DS1302 設置模式選擇位
  13. sbit ADD=P1^5; //增加
  14. sbit RED=P1^6; //減小
  15. sbit CANL=P1^7;
  16. void delay1ms(int i)//1 毫秒延時
  17. {
  18. int j,k;
  19. while(i--)
  20. for(j=76;j>1;j--);
  21. for(k=29;k>1;k--);
  22. }
  23. void delaynus(unsigned char n) //延時若干微秒
  24. {
  25. unsigned char i;
  26. for(i=0;i<n;i++);
  27. }
  28. /***********蜂鳴器模塊************/
  29. sbit beep=P1^5; //位定義，定義P.6 位fmp
  30. void dely500(void)
  31. {
  32. unsigned char i;
  33. for(i=250;i>0;i--)
  34. {
  35. _nop_();
  36. }
  37. }
  38. void baojing(unsigned char n)
  39. {
  40. unsigned char x,i;
  41. while(n--)
  42. {
  43. for(i=0;i<5;i++)
  44. {
  45. for(x=0;x<200;x++)
  46. {
  47. beep=~beep;
  48. dely500();
  49. }
  50. }
  51. for(i=0;i<3;i++)
  52. {
  53. for(x=0;x<200;x++)
  54. {
  55. beep=~beep;
  56. dely500();
  57. dely500();
  58. }
  59. }
  60. }
  61. }
  62. /*******DS1302 模塊*************/
  63. void Write1302(unsigned char date)//向1302 寫數據
  64. {
  65. unsigned char i;
  66. SCLK=0;
  67. delaynus(2);
  68. for(i=0;i<8;i++)
  69. {
  70. DATE=date&0x01;
  71. SCLK=1;
  72. delaynus(2);
  73. SCLK=0;
  74. delaynus(2);
  75. date>>=1;
  76. }
  77. }
  78. void WriteSet1302(unsigned char cmd,unsigned char date) //根據相應的命令輸入相應的數據
  79. {
  80. REST=0;
  81. SCLK=0;
  82. REST=1;
  83. Write1302(cmd);
  84. delaynus(5);
  85. Write1302(date);
  86. SCLK=1;
  87. REST=0;
  88. }
  89. unsigned char Read1302(void) //讀取1302 數據
  90. {
  91. unsigned char i,date;
  92. delaynus(2);
  93. for(i=0;i<8;i++)
  94. {
  95. date>>=1;
  96. if(DATE==1)
  97. date|=0x80;
  98. SCLK=1;
  99. delaynus(2);
  100. SCLK=0;
  101. delaynus(2);
  102. }
  103. return date;
  104. }
  105. unsigned char ReadSet1302(unsigned char cmd)//根據命令讀取1302 相應的值
  106. {
  107. unsigned char date;
  108. REST=0;
  109. SCLK=0;
  110. REST=1;
  111. Write1302(cmd);
  112. delaynus(2);
  113. date=Read1302();
  114. SCLK=1;
  115. REST=0;
  116. return date;
  117. }
  118. void IntDS1302(void) //DS1302 初始化
  119. {
  120. unsigned char flag;
  121. flag= ReadSet1302(0x81);
  122. if(flag&0x80) { //判斷時鐘芯片是否關閉
  123. WriteSet1302(0x8E,0x00); //根據寫狀態寄存器命令字，寫入不保護指令
  124. WriteSet1302(0x80,((0/10)<<4|(0%10))); //根據寫秒寄存器命令字，寫入秒的初始值
  125. WriteSet1302(0x82,((0/10)<<4|(0%10))); //根據寫分寄存器命令字，寫入分的初始值
  126. WriteSet1302(0x84,((0/10)<<4|(0%10))); //根據寫小時寄存器命令字，寫入小時的初始值
  127. WriteSet1302(0x86,((0/10)<<4|(0%10))); //根據寫日寄存器命令字，寫入日的初始值
  128. WriteSet1302(0x88,((0/10)<<4|(0%10))); //根據寫月寄存器命令字，寫入月的初始值
  129. WriteSet1302(0x8c,((10/10)<<4|(10%10))); //根據寫年寄存器命令字，寫入年的初始值
  130. WriteSet1302(0x90,0xa5); //打開充電功能選擇2K 電阻充電方式
  131. WriteSet1302(0x8E,0x80); //根據寫狀態寄存器命令字，寫入保護指令
  132. }
  133. }
  134. /***************液晶顯示模塊*****************/
  135. sbit RS=P2^6;
  136. sbit RW=P2^5;
  137. sbit E=P2^7;
  138. sbit BF=P0^7;
  139. /*液晶忙檢測*/
  140. bit BusyTest(void)
  141. {
  142. bit result;
  143. RS=0;
  144. RW=1;
  145. E=1;
  146. _nop_();
  147. _nop_();
  148. _nop_();
  149. result=BF;
  150. _nop_();
  151. _nop_();
  152. _nop_();
  153. E=0;
  154. return result;
  155. }
  156. /*寫指令*/
  157. void Write_com(unsigned char command)
  158. {
  159. while(BusyTest()!=0);
  160. RS=0;
  161. RW=0;
  162. E=0;
  163. _nop_();
  164. _nop_();
  165. _nop_();
  166. P0=command;
  167. _nop_();
  168. _nop_();
  169. _nop_();
  170. E=1;
  171. _nop_();
  172. _nop_();
  173. _nop_();
  174. E=0;
  175. }
  176. /*寫地址*/
  177. void Write_Address(unsigned char address)
  178. {
  179. Write_com(address|0x80);
  180. delay1ms(1);
  181. }
  182. /*寫數據*/
  183. void Write_Date(unsigned char date)
  184. {
  185. RS=1;
  186. RW=0;
  187. E=0;
  188. _nop_();
  189. _nop_();
  190. _nop_();
  191. P0=date;
  192. _nop_();
  193. _nop_();
  194. _nop_();
  195. E=1;
  196. _nop_();
  197. _nop_();
  198. _nop_();
  199. E=0;
  200. delay1ms(1);
  201. }
  202. /*初始化*/
  203. void Lcd_Int(void)
  204. {
  205. Write_com(0x38);
  206. delay1ms(1);
  207. Write_com(0x38);
  208. delay1ms(1);
  209. Write_com(0x06);
  210. delay1ms(1);
  211. Write_com(0x0c);
  212. delay1ms(1);
  213. Write_com(0x01);
  214. }
  215. void displaymainpart(void)//顯示液晶主要部分（不變化部分）
  216. {
  217. Write_Address(0x01);
  218. delay1ms(1);
  219. Write_Date('D');
  220. Write_Date('A');
  221. Write_Date('T');
  222. Write_Date('E');
  223. Write_Date(':');
  224. delay1ms(1);
  225. Write_Address(0x0A);
  226. delay1ms(1);
  227. Write_Date('-');
  228. Write_Address(0x0D);
  229. Write_Date('-');
  230. Write_Address(0x42);
  231. Write_Date('T');
  232. Write_Date('I');
  233. Write_Date('M');
  234. Write_Date('E');
  235. Write_Date(':');
  236. Write_Address(0x4A);
  237. Write_Date('-');
  238. Write_Address(0x4D);
  239. Write_Date('-');
  240. Write_Address(0x06);
  241. Write_Date('2');
  242. Write_Date('0');
  243. }
  244. void display_Second(unsigned char second) //在液晶上顯示秒
  245. {
  246. unsigned char i,j;
  247. i=second/10;
  248. j=second%10;
  249. Write_Address(0x4E);
  250. Write_Date(digit[i]);
  251. Write_Date(digit[j]);
  252. delay1ms(1);
  253. }
  254. void display_Minute(unsigned char minute) //在液晶上顯示分
  255. {
  256. unsigned char i,j;
  257. i=minute/10;
  258. j=minute%10;
  259. Write_Address(0x4B);
  260. Write_Date(digit[i]);
  261. Write_Date(digit[j]);
  262. delay1ms(1);
  263. }
  264. void display_Hour(unsigned char hour) //在液晶上顯示時
  265. {
  266. unsigned char i,j;
  267. i=hour/10;
  268. j=hour%10;
  269. Write_Address(0x48);
  270. Write_Date(digit[i]);
  271. Write_Date(digit[j]);
  272. delay1ms(1);
  273. }
  274. void display_Day(unsigned char day) //在液晶上顯示日
  275. {
  276. unsigned char i,j;
  277. i=day/10;
  278. j=day%10;
  279. Write_Address(0x0E);
  280. Write_Date(digit[i]);
  281. Write_Date(digit[j]);
  282. delay1ms(1);
  283. }
  284. void display_Month(unsigned char month) //在液晶上顯示月
  285. {
  286. unsigned char i,j;
  287. i=month/10;
  288. j=month%10;
  289. Write_Address(0x0B);
  290. Write_Date(digit[i]);
  291. Write_Date(digit[j]);
  292. delay1ms(1);
  293. }
  294. void display_Year(unsigned char year) //在液晶上顯示年
  295. {
  296. unsigned char i,j;
  297. i=year/10;
  298. j=year%10;
  299. Write_Address(0x08);
  300. Write_Date(digit[i]);
  301. Write_Date(digit[j]);
  302. delay1ms(1);
  303. }
  304. void display_houra(unsigned char x) //鬧鐘小時部分顯示
  305. {
  306. unsigned char i,j;
  307. i=x/10;
  308. j=x%10;
  309. Write_Address(0x44);
  310. Write_Date(digit[i]);
  311. Write_Date(digit[j]);
  312. }
  313. void display_minutea(unsigned char x)//鬧鐘分鐘部分顯示
  314. {
  315. unsigned char i,j;
  316. i=x/10;
  317. j=x%10;
  318. Write_Address(0x47);
  319. Write_Date(digit[i]);
  320. Write_Date(digit[j]);
  321. }
  322. void display_Time(void) //顯示實時時間
  323. {
  324. unsigned char value,day,month,year;
  325. Write_com(0x0c);
  326. value=ReadSet1302(0x81);
  327. seconds=(((value&0x70)>>4)*10+(value&0x0f));
  328. display_Second(seconds);
  329. value=ReadSet1302(0x83);
  330. minutes=(((value&0x70)>>4)*10+(value&0x0f));
  331. display_Minute(minutes);
  332. value=ReadSet1302(0x85);
  333. hours=(((value&0x70)>>4)*10+(value&0x0f));
  334. display_Hour(hours);
  335. value=ReadSet1302(0x87);
  336. day=(((value&0x70)>>4)*10+(value&0x0f));
  337. display_Day(day);
  338. value=ReadSet1302(0x89);
  339. month=(((value&0x70)>>4)*10+(value&0x0f));
  340. display_Month(month);
  341. value=ReadSet1302(0x8D);
  342. year=(((value&0xf0)>>4)*10+(value&0x0f));
  343. display_Year(year);
  344. }
  345. void displaystar(void) //顯示歡迎界面
  346. {
  347. unsigned char i,j;
  348. Write_Address(0x0f);
  349. while(displaywelcome[i]!='\0')
  350. {
  351. Write_Date(displaywelcome[i]);
  352. i++;
  353. delay1ms(1);
  354. }
  355. i=0;
  356. Write_Address(0x4f);
  357. while(displaywish[i]!='\0')
  358. {
  359. Write_Date(displaywish[i]);
  360. i++;
  361. delay1ms(1);
  362. }
  363. j=40;
  364. while(j--)
  365. {
  366. Write_com(0x18);//循環左移
  367. delay1ms(700);
  368. }
  369. Write_com(0x01);
  370. delay1ms(10);
  371. }
  372. void gbdisplay(unsigned char address) //時間調整時光標閃爍
  373. {
  374. Write_Address(address);
  375. delay1ms(5);
  376. Write_com(0x0f);
  377. delay1ms(5);
  378. }
  379. void displaymaxt(unsigned char x) //顯示最大溫度
  380. {
  381. unsigned char i,j,k;
  382. Write_com(0x0c);
  383. delay1ms(2);
  384. Write_Address(0x44);
  385. i=x/100;
  386. j=x/10;
  387. k=x%10;
  388. Write_Date(digit[i]);
  389. Write_Date(digit[j]);
  390. Write_Date(digit[k]);
  391. }
  392. /*****************時間調整部分*********************/
  393. void hourset(void) //調時
  394. {
  395. unsigned char timevalue,hour;
  396. delay1ms(500); //防止多次觸發
  397. WriteSet1302(0x8e,0x00);//將寫保護去掉，確保能正常將調整后的數值寫入DS1302
  398. timevalue=ReadSet1302(0x85); //讀取此時的數值
  399. hour=(((timevalue&0x70)>>4)*10+(timevalue&0x0f));
  400. while(1)
  401. {
  402. if(ADD==0)
  403. {
  404. delay1ms(50);
  405. if(ADD==0)
  406. {
  407. hour++;
  408. delay1ms(300);
  409. while(ADD==0);
  410. }
  411. }
  412. if(RED==0)
  413. {
  414. delay1ms(50);
  415. if(RED==0)
  416. {
  417. hour--;
  418. delay1ms(300);
  419. if(hour==0) hour=23;
  420. while(RED==0);
  421. }
  422. }
  423. timevalue=(((hour)/10)<<4|(hour%10));
  424. WriteSet1302(0x84,timevalue);
  425. delay1ms(1);
  426. display_Hour(hour);
  427. Write_Address(0x49);
  428. delay1ms(5);
  429. if(hour>=24) hour=0;
  430. delay1ms(5);
  431. if(CANL==0)
  432. {
  433. mode=0;
  434. Write_com(0x0c);
  435. break;
  436. }
  437. if(SET==0) break;
  438. }
  439. WriteSet1302(0x8e,0x80);
  440. }
  441. void minuteset(void) //調分
  442. {
  443. unsigned char timevalue,minute;
  444. delay1ms(500);
  445. WriteSet1302(0x8e,0x00);
  446. timevalue=ReadSet1302(0x83);
  447. minute=(((timevalue&0x70)>>4)*10+(timevalue&0x0f));
  448. while(1)
  449. {
  450. if(ADD==0)
  451. {
  452. delay1ms(10);
  453. if(ADD==0)
  454. {
  455. minute++;
  456. if(minute>=60) timevalue=0;
  457. while(ADD==0);
  458. }
  459. }
  460. if(RED==0)
  461. {
  462. delay1ms(10);
  463. if(RED==0)
  464. {
  465. minute--;
  466. delay1ms(300);
  467. if(minute==0) minute=59;
  468. while(RED==0);
  469. }
  470. }
  471. timevalue=((minute/10)<<4|(minute%10));
  472. WriteSet1302(0x82,timevalue);
  473. delay1ms(1);
  474. display_Minute(minute);
  475. Write_Address(0x4c);
  476. delay1ms(5);
  477. if(minute>=60) minute=0;
  478. delay1ms(5);
  479. if(CANL==0)
  480. {
  481. mode=0;
  482. Write_com(0x0c);
  483. break;
  484. }
  485. if(SET==0) break;
  486. }
  487. WriteSet1302(0x8e,0x80);
  488. }
  489. void secondset(void) //秒歸零
  490. {
  491. unsigned char second;
  492. delay1ms(500);
  493. WriteSet1302(0x8e,0x00);
  494. while(1)
  495. {
  496. if(ADD==0)
  497. {
  498. delay1ms(10);
  499. if(ADD==0)
  500. {
  501. second=0;
  502. WriteSet1302(0x80,0x00);
  503. while(ADD==0);
  504. }
  505. }
  506. delay1ms(1);
  507. display_Second(second);
  508. Write_Address(0x4f);
  509. delay1ms(5);
  510. if(CANL==0)
  511. {
  512. mode=0;
  513. Write_com(0x0c);
  514. break;
  515. }
  516. if(SET==0) break;
  517. }
  518. WriteSet1302(0x8e,0x80);
  519. }
  520. void yearset(void) //調年
  521. {
  522. unsigned char datevalue,year;
  523. delay1ms(500);
  524. WriteSet1302(0x8e,0x00);
  525. datevalue=ReadSet1302(0x8d);
  526. year=(((datevalue&0x70)>>4)*10+(datevalue&0x0f));
  527. while(1)
  528. {
  529. if(ADD==0)
  530. {
  531. delay1ms(10);
  532. if(ADD==0)
  533. {
  534. year++;
  535. while(ADD==0);
  536. }
  537. }
  538. if(RED==0)
  539. {
  540. delay1ms(10);
  541. if(RED==0)
  542. {
  543. year--;
  544. delay1ms(300);
  545. while(RED==0);
  546. }
  547. }
  548. datevalue=((year/10)<<4|(year%10));
  549. WriteSet1302(0x8c,datevalue);
  550. delay1ms(5);
  551. display_Year(year);
  552. delay1ms(5);
  553. Write_Address(0x09);
  554. delay1ms(5);
  555. if(CANL==0)
  556. {
  557. mode=0;
  558. Write_com(0x0c);
  559. break;
  560. }
  561. if(SET==0) break;
  562. }
  563. WriteSet1302(0x8e,0x80);
  564. }
  565. void monthset(void) //調月
  566. {
  567. unsigned char datevalue,month;

  569. delay1ms(500);
  570. WriteSet1302(0x8e,0x00);
  571. datevalue=ReadSet1302(0x89);
  572. month=(((datevalue&0x70)>>4)*10+(datevalue&0x0f));
  573. while(1)
  574. {
  575. if(ADD==0)
  576. {
  577. delay1ms(10);
  578. if(ADD==0)
  579. {
  580. month++;
  581. if(month>12) month=1;
  582. while(ADD==0);
  583. }
  584. }
  585. if(RED==0)
  586. {
  587. delay1ms(10);
  588. if(RED==0)
  589. {
  590. month--;
  591. delay1ms(300);
  592. if(month==0) month=12;
  593. while(RED==0);
  594. }
  595. }
  596. datevalue=((month/10)<<4|(month%10));
  597. WriteSet1302(0x88,datevalue);
  598. delay1ms(1);
  599. display_Month(month);
  600. Write_Address(0x0c);
  601. delay1ms(5);
  602. if(CANL==0)
  603. {
  604. mode=0;
  605. Write_com(0x0c);
  606. break;
  607. }
  608. if(SET==0) break;
  609. }
  610. WriteSet1302(0x8e,0x80);
  611. }
  612. void dayset(void) //調日
  613. {
  614. unsigned char datevalue,day;
  615. delay1ms(500);
  616. WriteSet1302(0x8e,0x00);
  617. datevalue=ReadSet1302(0x87);
  618. day=(((datevalue&0x70)>>4)*10+(datevalue&0x0f));
  619. while(1)
  620. {
  621. if(ADD==0)
  622. {
  623. delay1ms(10);
  624. if(ADD==0)
  625. {
  626. day++;
  627. if(day>31) day=1;
  628. while(ADD==0);
  629. }
  630. }
  631. if(RED==0)
  632. {
  633. delay1ms(10);
  634. if(RED==0)
  635. {
  636. day--;
  637. delay1ms(300);
  638. if(day==0) day=31;
  639. while(RED==0);
  640. }
  641. }
  642. datevalue=((day/10)<<4|(day%10));
  643. WriteSet1302(0x86,datevalue);
  644. delay1ms(1);
  645. display_Day(day);
  646. Write_Address(0x0f);
  647. delay1ms(5);
  648. if(CANL==0)
  649. {
  650. mode=0;
  651. Write_com(0x0c);
  652. break;
  653. }
  654. if(SET==0) break;
  655. }
  656. WriteSet1302(0x8e,0x80);
  657. }
  658. void alarmhourset(void) //鬧鐘小時調整
  659. {
  660. unsigned char value;
  661. value=houra;
  662. while(1)
  663. {
  664. if(ADD==0)
  665. {
  666. delay1ms(20);
  667. if(ADD==0)
  668. {
  669. Write_com(0x0c);
  670. delay1ms(5);
  671. value++;
  672. if(value>23) value=0;
  673. while(ADD==0);
  674. }
  675. }
  676. if(RED==0)
  677. {
  678. delay1ms(20);
  679. if(RED==0)
  680. {
  681. value--;
  682. if(value==0) value=23;
  683. while(RED==0);
  684. }
  685. }
  686. houra=value;
  687. display_houra(houra);
  688. gbdisplay(0x45);
  689. if(CANL==0)
  690. {
  691. delay1ms(500);
  692. break;
  693. }
  694. }
  695. }
  696. void alarmminuteset(void) //鬧鐘分鐘調整
  697. {
  698. while(1)
  699. {
  700. if(ADD==0)
  701. {
  702. delay1ms(20);
  703. if(ADD==0)
  704. {
  705. minutea++;
  706. if(minutea>59) minutea=0;
  707. while(ADD==0) ;
  708. }
  709. }
  710. if(RED==0)
  711. {
  712. delay1ms(20);
  713. if(RED==0)
  714. {
  715. minutea--;
  716. if(minutea==0) minutea=59;
  717. while(RED==0) ;
  718. }
  719. }
  720. display_minutea(minutea);
  721. gbdisplay(0x48);
  722. if(CANL==0)
  723. {
  724. delay1ms(500);
  725. break;
  726. }
  727. }
  728. }
  729. void TimeSet(void) //時間調整函數
  730. {
  731. display_Time();
  732. if(SET==0)
  733. {
  734. delay1ms(10);
  735. if(SET==0)
  736. {
  737. mode++;
  738. delay1ms(20);
  739. switch(mode)
  740. {
  741. case(1):{gbdisplay(0x48);hourset(); delay1ms(500);} break;
  742. case(2):{gbdisplay(0x4c);minuteset();delay1ms(500);} break;
  743. case(3):{gbdisplay(0x4f);secondset();delay1ms(500);} break;
  744. case(4):{gbdisplay(0x09);yearset();delay1ms(500);} break;
  745. case(5):{gbdisplay(0x0c);monthset();delay1ms(500);} break;
  746. case(6):{gbdisplay(0x0f);dayset();delay1ms(500);} break;
  747. }
  748. if(mode==7) mode=0;
  749. }
  750. }
  751. }
  752. /***************顯示溫度模塊********************/
  753. unsigned char code displayexplain[]={"Digit thermometer"};
  754. unsigned char code displayerror[]={"DS18B20 ERROR"};
  755. unsigned char code displayerror1[]={"PLEASE CHECK "};
  756. unsigned char code displaypart1[]={"WenDu:"};
  757. unsigned char code displaypart2[]={"Cent"};
  758. unsigned char flag;
  759. /**********************操作DS18B20 模塊***************************/
  760. sbit DQ=P3^7;
  761. unsigned char time;
  762. /**********************DS18B20 初始化****************************/
  763. bit IntDS18B20(void)
  764. {
  765. bit temp;
  766. DQ=1;
  767. for(time=0;time<2;time++);
  768. DQ=0;
  769. for(time=0;time<200;time++);
  770. DQ=1;
  771. for(time=0;time<10;time++);
  772. temp=DQ;
  773. for(time=0;time<200;time++);
  774. return temp;
  775. }
  776. /**************************讀DS18B20**********************/
  777. unsigned char ReadDS18B20(void)
  778. {
  779. unsigned char i;
  780. unsigned char dat;
  781. for(i=0;i<8;i++)
  782. {
  783. DQ=1;
  784. _nop_();
  785. DQ=0;
  786. _nop_();
  787. DQ=1;
  788. for(time=0;time<2;time++);
  789. dat>>=1;
  790. if(DQ==1)
  791. dat=dat|0x80;
  792. else
  793. dat=dat|0x00;
  794. for(time=0;time<10;time++);
  795. }
  796. return dat;
  797. }
  798. /*********************向DS18B20 寫數據**************************/
  799. void WriteDS18B20(unsigned char date)
  800. {
  801. unsigned char i;
  802. for(i=0;i<8;i++)
  803. {
  804. DQ=1;
  805. _nop_();
  806. DQ=0;
  807. DQ=date&0x01;
  808. for(time=0;time<10;time++);
  809. DQ=1;
  810. for(time=0;time<1;time++);
  811. date>>=1;
  812. }
  813. for(time=0;time<4;time++);
  814. }
  815. /*******************為讀取溫度做好準備************************/
  816. void ReadyreadDS18B20(void)
  817. {
  818. IntDS18B20();
  819. WriteDS18B20(0XCC);
  820. WriteDS18B20(0X44);
  821. delay1ms(200);
  822. IntDS18B20();
  823. WriteDS18B20(0XCC);
  824. WriteDS18B20(0XBE);
  825. }
  826. /*************在1602 液晶上顯示相關信息模塊**********************/
  827. /****************當未檢測到DS18B20 時顯示信息模塊****************/
  828. void Display_Error(void)
  829. {
  830. unsigned char i=0;
  831. Write_Address(0x00);
  832. while(displayerror[i]!='\0')
  833. {
  834. Write_Date(displayerror[i]);
  835. i++;
  836. delay1ms(100);
  837. }
  838. delay1ms(5);
  839. i=0;
  840. Write_Address(0x40);
  841. while(displayerror1[i]!='\0')
  842. {
  843. Write_Date(displayerror1[i]);
  844. i++;
  845. delay1ms(100);
  846. }
  847. delay1ms(3000) ;
  848. }
  849. /*************溫度顯示模塊****************/
  850. void Display_Explain(void)
  851. {
  852. unsigned char i=0;
  853. Write_Address(0x00);
  854. delay1ms(5);
  855. while(displayexplain[i]!='\0')
  856. {
  857. Write_Date(displayexplain[i]);
  858. i++;
  859. delay1ms(5);
  860. }
  861. i=0;
  862. Write_Address(0x40);
  863. while(displaypart1[i]!='\0')
  864. {
  865. Write_Date(displaypart1[i]);
  866. i++;
  867. delay1ms(5);
  868. }
  869. i=0;
  870. Write_Address(0x4C);
  871. while(displaypart2[i]!='\0')
  872. {
  873. Write_Date(displaypart2[i]);
  874. i++;
  875. delay1ms(5);
  876. }
  877. Write_Address(0x49);
  878. Write_Date('.');
  879. delay1ms(5);
  880. }
  881. /*********************顯示溫度整數部分*************************/
  882. void Display_Integer(unsigned char x)
  883. {
  884. unsigned char i,j,k;
  885. i=x/100;
  886. j=x%100/10;
  887. k=x%10;
  888. Write_Address(0x46);
  889. if(flag==1) Write_Date('-');
  890. Write_Date(digit[i]);
  891. Write_Date(digit[j]);
  892. Write_Date(digit[k]);
  893. delay1ms(50) ;
  894. }
  895. /************顯示溫度小數部分*********************/
  896. void Display_Decimal(unsigned char x)
  897. {
  898. Write_Address(0x4A);
  899. delay1ms(5);
  900. Write_Date(digit[x]);
  901. delay1ms(50);
  902. }
  903. void displayovert(void)
  904. {
  905. unsigned char i;
  906. Write_com(0x01);
  907. delay1ms(10);
  908. Write_Address(0x03);
  909. delay1ms(10);
  910. Write_Date('W');
  911. Write_Date('A');
  912. Write_Date('R');
  913. Write_Date('N');
  914. Write_Date('I');
  915. Write_Date('N');
  916. Write_Date('G');
  917. Write_Date('!');
  918. Write_Address(0x40);
  919. while(overtemperature[i]!='\0')
  920. {
  921. Write_Date(overtemperature[i]);
  922. i++;
  923. delay1ms(10);
  924. }
  925. }
  926. /*******************溫度主函數********************/
  927. void Temperature(void)
  928. {
  929. unsigned char i;
  930. delay1ms(5);
  931. if(IntDS18B20()!=0) Display_Error();
  932. else
  933. {
  934. delay1ms(1);
  935. Write_com(0x01);
  936. delay1ms(5);
  937. Display_Explain();
  938. for(length=50;length>0;length--)
  939. {
  940. for(i=0;i<6;i++)
  941. {
  942. flag=0;
  943. ReadyreadDS18B20();
  944. TL=ReadDS18B20();
  945. TH=ReadDS18B20();
  946. if((TH&0XF8)!=0X00)
  947. {
  948. flag=1;
  949. TL=~TL;
  950. TH=~TH;
  951. TL+=1;
  952. if(TL>255) TH+=1;
  953. TN=TH*16+TL/16;
  954. TD=(TL%16)*10/16;
  955. }
  956. TN=TH*16+TL/16;
  957. TD=(TL%16)*10/16;
  958. Display_Integer(TN);
  959. Display_Decimal(TD);
  960. delay1ms(10);
  961. }
  962. if(tempswitch==1)
  963. {
  964. if(TN>=Maxtemp)
  965. {
  966. Write_Address(0x03);
  967. delay1ms(5);
  968. displayovert();
  969. while(1)
  970. {
  971. baojing(1);
  972. if(CANL==0)
  973. {
  974. Write_com(0x01);
  975. delay1ms(5);
  976. break;
  977. }
  978. }
  979. }
  980. }
  981. if(CANL==0) break;
  982. }
  983. }
  984. }
  985. void tempset(void)
  986. {
  987. if(ADD==0)
  988. {
  989. delay1ms(10);
  990. if(ADD==0)
  991. {
  992. Maxtemp++;
  993. while(ADD==0);
  994. }
  995. }
  996. if(RED==0)
  997. {
  998. delay1ms(10);
  999. if(RED==0)
  1000. {
  1001. Maxtemp--;
  1002. while(RED==0);
  1003. }
  1004. }
  1005. }
  1006. void Maxtempset(void) //高溫報警設置
  1007. {
  1008. Write_com(0x01);
  1009. delay1ms(10);
  1010. Write_Address(0x03);
  1011. delay1ms(10);
  1012. Write_Date('T');
  1013. Write_Date('E');
  1014. Write_Date('M');
  1015. Write_Date('P');
  1016. Write_Address(0x09);
  1017. Write_Date('S');
  1018. Write_Date('E');
  1019. Write_Date('T');
  1020. Write_Address(0x40);
  1021. Write_Date('M');
  1022. Write_Date('A');
  1023. Write_Date('X');
  1024. Write_Date(':');
  1025. while(1)
  1026. {
  1027. if(SET==0)
  1028. {
  1029. delay1ms(20);
  1030. if(SET==0)
  1031. {
  1032. Write_Address(0x4e);
  1033. Write_com(0x0f);
  1034. while(1)
  1035. {
  1036. if(ADD==0)
  1037. {
  1038. delay1ms(20);
  1039. if(ADD==0)
  1040. {
  1041. Write_Address(0x4b);
  1042. delay1ms(5);
  1043. Write_Date('O');
  1044. Write_Date('N');
  1045. Write_Date(' ');
  1046. tempswitch=1;
  1047. }
  1048. }
  1049. if(RED==0)
  1050. {
  1051. delay1ms(20);
  1052. if(RED==0)
  1053. {
  1054. Write_Address(0x4b);
  1055. Write_Date('O');
  1056. Write_Date('F');
  1057. Write_Date('F');
  1058. tempswitch=0;
  1059. }
  1060. }
  1061. if(CANL==0)
  1062. {
  1063. delay1ms(500);
  1064. break;
  1065. }
  1066. }
  1067. }
  1068. }
  1069. if(tempswitch==1)
  1070. {
  1071. Write_Address(0x4b);
  1072. Write_Date('O');
  1073. Write_Date('N');
  1074. Write_Date(' ');
  1075. tempset();
  1076. displaymaxt(Maxtemp);
  1077. if(CANL==0)
  1078. {
  1079. Write_com(0x01);
  1080. displaymainpart();
  1081. break;
  1082. }
  1083. }
  1084. if(tempswitch==0)
  1085. {
  1086. Write_com(0x0c);
  1087. Write_Address(0x4b);
  1088. Write_Date('O');
  1089. Write_Date('F');
  1090. Write_Date('F');
  1091. }
  1092. if(CANL==0)
  1093. {
  1094. Write_com(0x01);
  1095. displaymainpart();
  1096. break;
  1097. }
  1098. }
  1099. }
  1100. void alarmswitchset(void)
  1101. {
  1102. while(1)
  1103. {
  1104. if(ADD==0)
  1105. {
  1106. delay1ms(100);
  1107. if(ADD==0)
  1108. {
  1109. alarmmode=1;
  1110. Write_Address(0x4c);
  1111. Write_Date('O');
  1112. Write_Date('N');
  1113. Write_Date(' ');
  1114. }
  1115. }
  1116. if(RED==0)
  1117. {
  1118. alarmmode=0;
  1119. Write_Address(0x4c);
  1120. Write_Date('O');
  1121. Write_Date('F');
  1122. Write_Date('F');
  1123. }
  1124. if(CANL==0)
  1125. {
  1126. delay1ms(500);
  1127. break;
  1128. }
  1129. }
  1130. }
  1131. /**************** 設置模塊******************/
  1132. void Set(void)
  1133. {
  1134. if(SET==0)
  1135. {
  1136. delay1ms(10);
  1137. if(SET==0)
  1138. {

  1140. Write_Address(0x40);
  1141. Write_Date('T');
  1142. Write_com(0x0f);
  1143. delay1ms(1000);
  1144. Write_com(0x0c);
  1145. while(1)
  1146. {
  1147. TimeSet();
  1148. if(ADD==0)
  1149. {
  1150. delay1ms(20);
  1151. if(ADD==0)
  1152. {
  1153. Write_com(0x01);
  1154. Write_Address(0x00);
  1155. delay1ms(5);
  1156. Write_Date('S');
  1157. delay1ms(10);
  1158. Maxtempset();
  1159. }
  1160. }
  1161. if(RED==0)
  1162. {
  1163. delay1ms(20);
  1164. if(RED==0)
  1165. {
  1166. Write_com(0x01);
  1167. delay1ms(5);
  1168. Write_Address(0x02);
  1169. Write_Date('A');
  1170. Write_Date('L');
  1171. Write_Date('A');
  1172. Write_Date('R');
  1173. Write_Date('M');
  1174. Write_Address(0x09);
  1175. Write_Date('S');
  1176. Write_Date('E');
  1177. Write_Date('T');
  1178. Write_Address(0x46);
  1179. Write_Date('-');
  1180. display_houra(houra);
  1181. display_minutea(minutea);
  1182. if(alarmmode==1)
  1183. {
  1184. Write_Address(0x4c);
  1185. Write_Date('O');
  1186. Write_Date('N');
  1187. Write_Date(' ');
  1188. }
  1189. if(alarmmode==0)
  1190. {
  1191. Write_Address(0x4c);
  1192. Write_Date('O');
  1193. Write_Date('F');
  1194. Write_Date('F');
  1195. }
  1196. while(1)
  1197. {
  1198. if(SET==0)
  1199. {
  1200. delay1ms(100);
  1201. if(SET==0)
  1202. {
  1203. amode++;
  1204. switch(amode)
  1205. {
  1206. case(1):{gbdisplay(0x45);alarmhourset();Write_com(0x0c);delay1ms(500);} break;
  1207. case(2):{gbdisplay(0x48);alarmminuteset();Write_com(0x0c);delay1ms(500);} break;
  1208. case(3):{gbdisplay(0x4c);alarmswitchset();Write_com(0x0c);delay1ms(500);} break;
  1209. }
  1210. if(amode==4) amode=0;
  1211. }
  1212. }
  1213. if(CANL==0)
  1214. {
  1215. Write_com(0x01);
  1216. delay1ms(5);
  1217. displaymainpart();
  1218. break;
  1219. }
  1220. }
  1221. }
  1222. }
  1223. if(CANL==0)
  1224. {
  1225. Write_Address(0x40);
  1226. Write_Date(' ');
  1227. Write_com(0x0c);
  1228. break;
  1229. }
  1230. }
  1231. }
  1232. }
  1233. }
  1234. /***************主函數**********************/
  1235. void main()
  1236. {
  1237. IE=0X82; //打開定時中斷
  1238. TMOD=0X01; //選擇定時器0 工作在方式1
  1239. TR0=0; //啟動定時器0
  1240. IntDS1302(); //初始化DS1302
  1241. delay1ms(1);
  1242. Lcd_Int(); //1602 液晶初始化
  1243. delay1ms(2);
  1244. displaystar(); //顯示歡迎界面
  1245. displaymainpart(); //顯示主要部分（不變化）
  1246. while(1)
  1247. {
  1248. display_Time( );
  1249. Set( );
  1250. if(ADD==0)
  1251. {
  1252. Write_com(0x01);
  1253. delay1ms(5);
  1254. Temperature();
  1255. Write_com(0x01);
  1256. displaymainpart();
  1257. }
  1258. if((hours==houra)&&(minutes==minutea)&&(seconds==0))
  1259. {
  1260. if(alarmmode==1)
  1261. {
  1262. Write_com(0x01);
  1263. delay1ms(5);
  1264. Write_Address(0x03);
  1265. Write_Date('T');
  1266. Write_Date('I');
  1267. Write_Date('M');
  1268. Write_Date('E');
  1269. Write_Address(0x08);
  1270. Write_Date('U');
  1271. Write_Date('P');
  1272. Write_Date('!');
  1273. delay1ms(5);
  1274. while(1)
  1275. {
  1276. baojing(1);
  1277. if(CANL==0)
  1278. {
  1279. Write_com(0x01);
  1280. delay1ms(5);
  1281. displaymainpart();
  1282. break;
  1283. }
  1284. }
  1285. }
  1286. }
  1287. }
  1288. }
復制代碼
作者: yuyuanhpu    時間: 2021-6-4 21:44
好想學習一下，為了別人重新?lián)炱鹗昵皩W(xué)的東西，希望能審核通過
作者: wei2001    時間: 2021-6-10 13:55
啥啊    代碼和圖都不是配套的     代碼用的接口和圖用的接口就不一樣




歡迎光臨 (http://www.torrancerestoration.com/bbs/) Powered by Discuz! X3.1