最近中文字幕MV在线视频2019,亚洲精品久久中文日本

標題: 基于kea128的電磁式智能小車 [打印本頁]

作者: chenao 時間: 2018-7-2 17:03
標題: 基于kea128的電磁式智能小車
#include  "includefile.h"

/**********全局變量定義********/
int32 LeftDead = 0;
int32 RighDead = 0;
float Ratio_Encoder_Left = 207/(1175*0.02);// 左輪速度=counter*左輪周長(mm)/(左輪轉一圈對應的脈沖數*程序周期)
float Ratio_Encoder_Righ = 207/(1175*0.02);// 右輪速度=counter*右輪周長(mm)/(右輪轉一圈對應的脈沖數*程序周期)
float g_fRealSpeed = 0; //真實速度
float g_fLeftRealSpeed;
float g_fRighRealSpeed;
float g_fSpeedFilter = 0; //階梯濾波速度
float g_fExpectSpeed = 2800; //期望速度
float g_fSpeedError; //速度偏差
float g_fSpeedErrorTemp[5] = {0};
float fSpeedErrorInteg = 0;
int32 g_nLeftpulse = 0,g_nRighpulse = 0;
float g_PWMOut;
int32 g_nLeftPWM, g_nRighPWM;
//速度控制
float g_speedControl_P = 320; //速度P
float g_speedControl_I = 100; //速度I
float g_fSpeedControlOut = 0; //速度輸出

/**
* @file PWM輸出
* @date 2018
*/
void PWMOut(void)
{
int32 nLeftPWM = 0, nRighPWM = 0;

if(Flag_Speed == OFF) g_fSpeedControlOut = 0; //如果Flag_Speed == OFF 不輸出速度
if(Flag_Direction == OFF) g_fDirectionControlOut = 0; //如果Flag_Direction == OFF 不輸出方向

g_nLeftPWM = (int32)(g_fSpeedControlOut - g_fDirectionControlOut);
g_nRighPWM = (int32)(g_fSpeedControlOut + g_fDirectionControlOut);

// g_nLeftPWM = g_nLeftPWM*1.05;//電機差異補償
// g_nRighPWM = g_nRighPWM;

if(Flag_Stop == OFF) //如果Flag_Stop == OFF電機輸出0
{
      g_nLeftPWM = 0;g_nRighPWM = 0;
}

    if(g_nLeftPWM < 0)
{
nLeftPWM = LeftDead - g_nLeftPWM;
nLeftPWM = (nLeftPWM > 900? 900: nLeftPWM);
ftm_pwm_duty(ftm2, ftm_ch2, nLeftPWM);
ftm_pwm_duty(ftm2, ftm_ch3, 0);
}
else
{
nLeftPWM = LeftDead + g_nLeftPWM;
nLeftPWM = (nLeftPWM > 900? 900: nLeftPWM);
ftm_pwm_duty(ftm2, ftm_ch2, 0);
ftm_pwm_duty(ftm2, ftm_ch3, nLeftPWM);
}

if(g_nRighPWM < 0)
{
nRighPWM = RighDead - g_nRighPWM;
nRighPWM = (nRighPWM > 900? 900: nRighPWM);
ftm_pwm_duty(ftm2, ftm_ch4, 0);
ftm_pwm_duty(ftm2, ftm_ch5, nRighPWM);
}
else
{
nRighPWM = RighDead + g_nRighPWM;
nRighPWM = (nRighPWM > 900? 900: nRighPWM);
ftm_pwm_duty(ftm2, ftm_ch4, nRighPWM);
ftm_pwm_duty(ftm2, ftm_ch5, 0);
}
}

/**
* @file 計算速度偏差
* @note       產生全局變量g_fSpeedError
* @date 2017
*/
void CalSpeedError(void)
{
static float fSpeedOld = 0, fSpeedNew = 0;

g_nLeftpulse = (gpio_get(Coder_dir_left) ==1?ftm_count_get(ftm0):-ftm_count_get(ftm0));//讀取左輪脈沖
ftm_count_clean(ftm0);
g_nRighpulse = (gpio_get(Coder_dir_right)==0?ftm_count_get(ftm1):-ftm_count_get(ftm1));//讀取右輪脈沖
ftm_count_clean(ftm1);

g_fLeftRealSpeed = g_nLeftpulse*Ratio_Encoder_Left;
g_fLeftRealSpeed = (g_fLeftRealSpeed>3400?3400:g_fLeftRealSpeed); //濾左編碼器的噪聲
g_fRighRealSpeed = g_nRighpulse*Ratio_Encoder_Righ;
g_fRighRealSpeed = (g_fRighRealSpeed>3400?3400:g_fRighRealSpeed); //濾右編碼器的噪聲

g_fRealSpeed = (g_fLeftRealSpeed + g_fRighRealSpeed)*0.5; //真實速度

//速度采集梯度平滑，每次采集最大變化200
fSpeedOld = g_fSpeedFilter;
fSpeedNew = g_fRealSpeed;

if(fSpeedNew>=fSpeedOld)
g_fSpeedFilter = ((fSpeedNew-fSpeedOld)>300?(fSpeedOld+300):fSpeedNew);
else
g_fSpeedFilter = ((fSpeedNew-fSpeedOld)<-300?(fSpeedOld-300):fSpeedNew);

//flash中參數
// g_fExpectSpeed = float05;  //2800

g_fSpeedError =  g_fExpectSpeed - g_fSpeedFilter;
g_fSpeedErrorTemp[4] = g_fSpeedErrorTemp[3];
g_fSpeedErrorTemp[3] = g_fSpeedErrorTemp[2];
g_fSpeedErrorTemp[2] = g_fSpeedErrorTemp[1];
g_fSpeedErrorTemp[1] = g_fSpeedErrorTemp[0];
g_fSpeedErrorTemp[0] = g_fSpeedError;

}

/**
* @file 速度控制
* @note       速度梯度平滑
* @date 2017
*/
void SpeedControl(void)
{
int8 index=1;

CalSpeedError(); //計算速度偏差
g_fSpeedError = (g_fSpeedError>800?800:g_fSpeedError);//速度偏差限幅
//flash中參數
// g_speedControl_P = float06; //320
// g_speedControl_I = float07; //100

//積分分離
if((g_fSpeedError<=300)&&(g_fSpeedError>=-300))
index=1;
else
index=0;
fSpeedErrorInteg = index *float08 * g_fSpeedError * 0.00001;

if(Flag_Stop==OFF|Flag_Speed==OFF)
{
fSpeedErrorInteg = 0; //停車積分清零
}
//fSpeedErrorInteg = (fSpeedErrorInteg < 0.0? 0.0: fSpeedErrorInteg);//積分下限
//fSpeedErrorInteg = (fSpeedErrorInteg > 400.0? 400.0: fSpeedErrorInteg);//積分上限
//速度控制算法（增量式PI）
g_fSpeedControlOut += g_speedControl_P*0.005*(g_fSpeedErrorTemp[0]-g_fSpeedErrorTemp[1]) + fSpeedErrorInteg;
g_fSpeedControlOut = (g_fSpeedControlOut>=6000?6000:g_fSpeedControlOut);

}

QQ圖片20180702165758.png (7.76 KB, 下載次數: 133)

QQ圖片20180702165846.png (111.55 KB, 下載次數: 139)

電磁三輪車.zip

4.76 MB, 下載次數: 38, 下載積分: 黑幣 -5

作者: chenao 時間: 2018-7-2 17:03
供大家學習參考

作者: 1531225810 時間: 2018-7-6 10:09
比賽可以用嗎

作者: xx不放火 時間: 2019-12-8 10:59
感謝！！不過還是有些看不懂

歡迎光臨 (http://www.torrancerestoration.com/bbs/)