国产爆乳无码无圣光在线观看,少妇性色午夜婬片AAA播放

標題: 幫忙注釋下程序，跪求大佬 [打印本頁]

作者: forever1996 時間: 2018-7-5 00:12
標題: 幫忙注釋下程序，跪求大佬
#include <reg52.h>
//#include <intrins.h>
//#include <string.h>
//#include <math.h>
//#include "stdio.h"
//#include <stdarg.h>
//#include<stdlib.h>
#include"lcd.h"
#include"iic.h"
#define uchar unsigned char
#define uint unsigned int

sbit RED = P3^5;
sbit YELLOW = P3^6;
sbit GREEN = P3^7;

int AD;       //AD
int CYCLE; //電壓
float CYC; //電壓
int ELE;//電量（百分比）
void delay(uint z)
{
uint x,y;
for(x=z;x>0;x--)
for(y=120;y>0;y--);
}

void main()
{
LcdInit();
   init_pcf8591(0x03);
RED = 0;YELLOW=0;GREEN=0;
while(1)
{
AD  =  adc_pcf8591();

      LcdWriteCom(0x80);
LcdWriteData('A');
LcdWriteData('D');
LcdWriteData(':');
LcdWriteData('0'+AD/100);
LcdWriteData('0'+AD/10%10);
LcdWriteData('0'+AD%10);

CYC = (AD*100)/51;
CYCLE = CYC;
      LcdWriteCom(0x80+0X40);
      LcdWriteData('V');
LcdWriteData('O');
LcdWriteData(':');
LcdWriteData('0'+CYCLE/100);
      LcdWriteData('.');
LcdWriteData('0'+CYCLE/10%10);
LcdWriteData('0'+CYCLE%10);
LcdWriteData('V');

   //3.20V-4.20V

ELE = CYCLE-320;
LcdWriteCom(0x8A+0X40);
LcdWriteData('E');
LcdWriteData(':');
    LcdWriteData('0'+ELE/100);
LcdWriteData('0'+ELE/10%10);
LcdWriteData('0'+ELE%10);
LcdWriteData('%');

switch(ELE/10%10)
{
   case 0: case 1: case 2: case 3: {RED = 1;YELLOW=0;GREEN=0;} break;//電量在0-30% 紅燈亮
   case 4: case 5: case 6: case 7: {RED = 0;YELLOW=1;GREEN=0;} break;
   case 8: case 9:       {RED = 0;YELLOW=0;GREEN=1;} break;
   default :    {RED = 0;YELLOW=0;GREEN=0;} break;
}
// delay(100);
}
}

作者: 小貓貓愛吃魚 時間: 2018-7-5 09:29
男兒膝下有黃金，只跪蒼天和娘親；男兒滿腔熱血情，只報家國與人民。

作者: 清溪明月 時間: 2018-7-5 12:12
讀取并顯示電壓以及電量百分比并依據不同的百分比驅動不同的指示燈

作者: 兔斯基 時間: 2018-7-6 17:20

#include <reg52.h>                   //包含單片機的頭文件
//#include <intrins.h>
//#include <string.h>
//#include <math.h>
//#include "stdio.h"
//#include <stdarg.h>
//#include<stdlib.h>
#include"lcd.h"                      //包含LCD的頭文件
#include"iic.h"                      //包含IIC通信的頭文件

#define uchar unsigned char          //自定義的數據類型
#define uint unsigned int          //自定義的數據類型

sbit RED       = P3^5;             //定義RED接在單片機的P3^5引腳上
sbit YELLOW = P3^6;                //定義YELLOW接在單片機的P3^6引腳上
sbit GREEN       = P3^7;          //定義GREEN接在單片機的P3^7引腳上

int AD;                            //AD
int CYCLE;                         //電壓
float CYC;                         //電壓
int ELE;                            //電量（百分比）

/******************************************//*
*
*函數名：void delay(uint z)
*參數：uint z
*返回值：void
*函數功能：延時函數
*
*//******************************************/
void delay(uint z)
{
      uint x,y;
      for(x=z;x>0;x--)
            for(y=120;y>0;y--);
}

/******************************************//*
*
*函數名：int main()    改為int main()
*參數：void
*返回值：int
*函數功能：主函數
*
*//******************************************/
void main()
{
LcdInit();                            //調用LCD初始化函數，進行LCD的初始化
init_pcf8591(0x03);                   //應該也是個初始化函數
      RED = 0;YELLOW=0;GREEN=0;          //讓RED,YELLOW,GREEN引腳都為零

      while(1)
      {
            AD  =  adc_pcf8591();    //采集電壓，讓數值送入AD變量

      LcdWriteCom(0x80);                //對LCD顯示屏進行寫命令
            LcdWriteData('A');       //對LCD顯示屏進行寫數據（顯示的東西）
            LcdWriteData('D');
            LcdWriteData(':');
            LcdWriteData('0'+AD/100); //‘0’+AD/100這個加‘0’的意思是進行ASCII碼的轉換
            LcdWriteData('0'+AD/10%10);
            LcdWriteData('0'+AD%10);

            CYC = (AD*100)/51;       //CYC變量進行運算
            CYCLE = CYC;
         LcdWriteCom(0x80+0X40);       //對LCD顯示屏進行寫命令
      LcdWriteData('V');                //對LCD顯示屏進行寫數據（顯示的東西）
            LcdWriteData('O');
            LcdWriteData(':');
            LcdWriteData('0'+CYCLE/100);
         LcdWriteData('.');
            LcdWriteData('0'+CYCLE/10%10);
            LcdWriteData('0'+CYCLE%10);
            LcdWriteData('V');

         //3.20V-4.20V

            ELE = CYCLE-320;
            LcdWriteCom(0x8A+0X40);
            LcdWriteData('E');
            LcdWriteData(':');
               LcdWriteData('0'+ELE/100);
            LcdWriteData('0'+ELE/10%10);
            LcdWriteData('0'+ELE%10);
            LcdWriteData('%');


//以下內容就是對數據進行選擇處理，讀取并顯示電壓以及電量百分比  并依據不同的百分比驅動不同的指示燈
            switch(ELE/10%10)
            {
                     case 0:
                     case 1:
                     case 2:
                     case 3:
                     {
                           RED = 1;
                           YELLOW=0;
                           GREEN=0;
                        } break;                   //電量在0-30% 紅燈亮
                     case 4:
                     case 5:
                     case 6:
                     case 7:
                     {
                           RED = 0;
                           YELLOW=1;
                           GREEN=0;
                        } break;
                     case 8: case 9:                                  {RED = 0;YELLOW=0;GREEN=1;} break;
                     default :                                                 {RED = 0;YELLOW=0;GREEN=0;} break;
            }
//                delay(100);
}
}

作者: duo1.. 時間: 2018-7-7 09:05
這個程序挺復雜的囧語C語言寫的

作者: zhangyihan123 時間: 2018-7-7 09:55
就是紅綠燈啊，通過延遲函數，判斷哪個燈亮

歡迎光臨 (http://www.torrancerestoration.com/bbs/)