標題: STM32 cubemx配置工程-LED代碼 [打印本頁]
作者: 柱子111    時間: 2019-4-23 12:49
標題: STM32 cubemx配置工程-LED代碼
自己剛比賽完發現了很多不會的東西
現在好多東西都需要重新學習一下

因此上傳寫基礎的代碼代表自己學習的進度



單片機源程序如下:
  1. /* Includes ------------------------------------------------------------------*/
  2. #include "stm32f4xx_hal.h"
  3. #include "gpio.h"

  5. /* USER CODE BEGIN Includes */

  7. /* USER CODE END Includes */

  9. /* Private variables ---------------------------------------------------------*/

  11. /* USER CODE BEGIN PV */
  12. /* Private variables ---------------------------------------------------------*/

  14. /* USER CODE END PV */

  16. /* Private function prototypes -----------------------------------------------*/
  17. void SystemClock_Config(void);

  19. /* USER CODE BEGIN PFP */
  20. /* Private function prototypes -----------------------------------------------*/

  22. /* USER CODE END PFP */

  24. /* USER CODE BEGIN 0 */

  26. /* USER CODE END 0 */

  28. int main(void)
  29. {

  31.   /* USER CODE BEGIN 1 */

  33.   /* USER CODE END 1 */

  35.   /* MCU Configuration----------------------------------------------------------*/

  37.   /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  38.   HAL_Init();

  40.   /* Configure the system clock */
  41.   SystemClock_Config();

  43.   /* Initialize all configured peripherals */
  44.   MX_GPIO_Init();

  46.   /* USER CODE BEGIN 2 */

  48.   /* USER CODE END 2 */

  50.   /* Infinite loop */
  51.   /* USER CODE BEGIN WHILE */
  52.   while (1)
  53.   {
  54.   /* USER CODE END WHILE */

  56.   /* USER CODE BEGIN 3 */
  57.   HAL_GPIO_WritePin(led1_GPIO_Port, led1_Pin, GPIO_PIN_RESET);
  58.                   HAL_GPIO_WritePin(led0_GPIO_Port, led0_Pin, GPIO_PIN_SET);
  59.                 HAL_Delay(100);
  60.                  HAL_GPIO_WritePin(led0_GPIO_Port, led0_Pin, GPIO_PIN_RESET);
  61.                   HAL_GPIO_WritePin(led1_GPIO_Port, led1_Pin, GPIO_PIN_SET);
  62.                 HAL_Delay(100);
  63.                
  64.   }
  65.   /* USER CODE END 3 */

  67. }

  69. /** System Clock Configuration
  70. */
  71. void SystemClock_Config(void)
  72. {

  74.   RCC_OscInitTypeDef RCC_OscInitStruct;
  75.   RCC_ClkInitTypeDef RCC_ClkInitStruct;

  77.   __HAL_RCC_PWR_CLK_ENABLE();

  79.   __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  81.   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  82.   RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  83.   RCC_OscInitStruct.HSICalibrationValue = 16;
  84.   RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  85.   HAL_RCC_OscConfig(&RCC_OscInitStruct);

  87.   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
  88.                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  89.   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  90.   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  91.   RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  92.   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
  93.   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0);

  95.   HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);

  97.   HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);

  99.   /* SysTick_IRQn interrupt configuration */
  100.   HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
  101. }

  103. /* USER CODE BEGIN 4 */

  105. /* USER CODE END 4 */

  107. #ifdef USE_FULL_ASSERT

  109. /**
  110.    * @brief Reports the name of the source file and the source line number
  111.    * where the assert_param error has occurred.
  112.    * @param file: pointer to the source file name
  113.    * @param line: assert_param error line source number
  114.    * @retval None
  115.    */
  116. void assert_failed(uint8_t* file, uint32_t line)
  117. {
  118.   /* USER CODE BEGIN 6 */
  119.   /* User can add his own implementation to report the file name and line number,
  120.     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  121.   /* USER CODE END 6 */

  123. }

  125. #endif

  127. /**
  128.   * @}
  129.   */

  131. /**
  132.   * @}
  133. */

  135. /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
復制代碼

所有資料51hei提供下載:
LED1.7z (277.07 KB, 下載次數: 5)






歡迎光臨 (http://www.torrancerestoration.com/bbs/) Powered by Discuz! X3.1