8090超碰人人做人人爽,亚洲av中文无码字幕色本草,久久精品欧美一区二区三区不卡

標題: 51單片機洗衣機設計 Proteus仿真原理圖程序代碼 [打印本頁]

作者: Stantayp 時間: 2019-6-9 12:54
標題: 51單片機洗衣機設計 Proteus仿真原理圖程序代碼
單片機洗衣機的仿真原理圖如下（proteus仿真工程文件可到本帖附件中下載）

單片機代碼如下
#include <REG52.H>
#define uchar unsigned char
#define uint  unsigned int
#define qiang_ledon qiang_led=1;
#define qiang_ledoff qiang_led=0;
#define biao_ledon biao_led=1;
#define biao_ledoff biao_led=0;
#define ruo_ledon ruo_led=1;
#define ruo_ledoff ruo_led=0;
#define piao_ledon piao_led=1;
#define piao_ledoff piao_led=0;
#define sgan_ledon sgan_led=1;
#define sgan_ledoff sgan_led=0;
#define jin_ledon jin_led=1;
#define jin_ledoff jin_led=0;
#define pai_ledon pai_led=1;
#define pai_ledoff pai_led=0;
unsigned char code Tab[11]={0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F}; //數碼管顯示0～9的段碼表
unsigned char int_time;       //記錄中斷次數
unsigned char second;       //儲存秒
uint t=0,tt=0;
sbit k1=P0^0;
sbit k2=P0^1;
sbit k3=P0^2;
sbit sg=P0^3;
sbit hk1=P0^4;
sbit hk2=P0^5;
sbit ledon=P0^7;
sbit qiang_led=P2^0;
sbit biao_led=P2^1;
sbit ruo_led=P2^2;
sbit piao_led=P2^3;
sbit sgan_led=P2^4;
sbit jin_led=P2^5;
sbit pai_led=P2^6;
sbit p30=P3^0;
sbit p31=P3^1;
sbit beepon=P2^7;
sbit sm1=P3^6;
sbit sm2=P3^7;
void delay2(void)
{
  unsigned char m;
  for(m=0;m<200;m++)
      ;
}

void delay1(int s)
{
int i;
for(;s>0;s--)
for(i=0;i<65;i++);
}

void delay(uint i)
{
uchar j;
for(i;i>0;i--)
for(j=255;j>0;j--);
}

void DisplaySecond(unsigned char k)
{

sm1=0;       //P2.6引腳輸出低電平， DS6點亮
P1=Tab[k/10];       //顯示十位
   delay2();
   delay2();
sm1=1;
sm2=0;    //P2.7引腳輸出低電平， DS7點亮
P1=Tab[k%10];       //顯示個位
   delay2();
   delay2();
P3=0xff;    //關閉所有數碼管
P1=1;       //顯示個位
   delay2();
   delay2();
}

void beep()
{
      p30=0;
p31=0;
         t=0;
      while(1)
      {
      beepon^=1;
   delay(300);
   if(t>=80) break;
      }
      beepon=0;
      biao_led=0;
}

void f_qiang()
{
      qiang_ledon;
      t=0;
      tt=0;
   int_time=0;
   second=00;
      while(1)
{
      if(tt>=400) break;
   t=0;
      while(t<80&&tt<=400)
      {
         p31=0;
         p30=1;       //正轉 4s
      DisplaySecond(second);
         }
      t=0;       //反轉 4s
      while(t<80&&tt<=400)
      {
         p30=0;
         p31=1;
         DisplaySecond(second);
         }
   }
      p30=0;
      p31=0;
   }

void f_biao()
      {
      qiang_led=0;
   biao_led=1;
      t=0;
      tt=0;
   int_time=0;
   second=00;
      while(1)
   {
         if(tt>=400) break;
         t=0;
      while(t<60&&tt<=400)
         {
      p31=0;
               p30=1;       //正轉3s
      DisplaySecond(second);
   }

            t=0;       //反轉3s
      while(t<60&&tt<=400)
   {
            p30=0;
               p31=1;
               DisplaySecond(second);
            }
   }
   p30=0;
         p31=0;
      }

void f_ruo()
{
      qiang_led=0;
      biao_led=0;
      ruo_led=1;
      t=0;
      tt=0;
   int_time=0;
   second=00;
            while(1)
   {
                  if(tt>=400) break;
               t=0;
            while(t<40&&tt<=400)
         {       p31=0;
                     p30=1;       //正轉2s
            DisplaySecond(second);
            }
         t=0;       //反轉 2s
            while(t<40&&tt<=400)
         { p30=0;
                     p31=1;
                     DisplaySecond(second);
                  }
      }
            p30=0;
         p31=0;
   }

void f_piao()
      {
         qiang_ledoff;
         biao_ledoff;
         piao_ledon;
         t=0;
         tt=0;
   int_time=0;
   second=00;
               while(1)
      {
                  if(tt>=400) break;
               t=0;
               while(t<40&&tt<=400)
            {       p31=0;
                     p30=1;       //正轉2s
                  DisplaySecond(second);
               }
               t=0;       //反轉2s
               while(t<40&&tt<=400)
            { p30=0;
                        p31=1;
                           DisplaySecond(second);
                     }
         }
      p30=0;
   p31=0;
      piao_ledoff;
      }

void pai_leds()
   {
         p30=0;
         p31=0;
            pai_led=1;       //排水閥燈亮等待霍爾開關2
         while(hk2);
         if(hk2==0)  //如果閉合
         pai_led=0;       //排水燈滅
   }

void jin()
{
         p30=0;
         p31=0;
         jin_ledon;
         while(hk1);
         if(hk1==0)
         jin_ledoff;
   }

void sgan()
{
         sgan_ledon;       //甩干燈亮
         t=0;
      int_time=0;
      second=00;
         while(t<=400)
         {
                        p31=0;
                     p30=1;
            DisplaySecond(second);
               }
      sgan_ledoff;
}

void sgan1()
{
         sgan_ledon;
         t=0;
   int_time=0;
   second=00;
         while(t<=400)
         {
                        p31=0;
               p30=1;
            DisplaySecond(second);
               }
      piao_ledoff;
      sgan_ledoff;
      beep();
         t=401;
}

void f_an1()
{
      qiang_ledon; //方案1燈亮
      jin();  //進入強洗
      f_qiang();       //循環20S
      delay1(4000);//延時4s
      f_biao();  //循環20S
      delay1(4000);//延時4s
      f_ruo();  //循環20S
      ruo_ledoff;
      pai_leds();
      delay1(1000); //延時1S 進入甩干
      sgan(); //甩干20s
      sgan_ledoff;
      ruo_ledoff;
      piao_ledoff;
      jin();
      delay1(1000); //延時1S 進入漂洗
      f_piao();  //循環20S
      sgan_ledoff;
      piao_ledoff;
      pai_leds();
      delay1(1000); //延時1S 進入甩干
      sgan1();//最終甩干20S
      delay(500);//延時
      beep();
}

void f_an2()
{
      biao_ledon; //方案1燈亮
      jin();
      f_biao();  //循環20S
      delay1(4000); //延時4S
      f_ruo();  //循環20S
      ruo_ledoff;
      pai_leds();
      delay1(1000); //延時1S 進入甩干
      sgan(); //甩干20s
      ruo_ledoff;
      piao_ledoff;
      jin();
      delay1(1000); //延時1S 進入漂洗
      f_piao();  //循環20S
      sgan_led=0;
      pai_leds();
      delay1(1000); //延時1S 進入甩干
      sgan();//最終甩干20s
      delay(500);//延時5s
      piao_led=0;
      beep();
}

void f_an3()
  {
      ruo_led=1; //方案1燈亮
      jin();
      f_ruo();  //循環20S
      ruo_ledoff;
      pai_leds();
      delay1(1000); //延時1S 進入甩干
      sgan(); //甩干20S
      ruo_ledoff;
      piao_ledoff;
      jin();
      delay1(1000); //延時1S 進入漂洗
      f_piao();  //循環20S
      sgan_led=0;
      pai_leds();
      delay1(1000); //延時1S 進入甩干
      sgan();//最終甩干20s
      delay(500);//延時5s
      piao_led=0;
      p30=0;
      beep();
}

int main(void)
{
  TMOD=0x01;    //方式1 16位計數器
  TH0=-50000/256; //設定初值
  TL0=-50000%256;
  EA=1;             //開總中斷
  ET0=1;          //開定時器0中斷
  TR0=1;          //啟動定時器0
  P2=0;
  int_time=0;    //中斷次數初始化
  second=00;          //秒初始化
      while(1)
{
      if(k1==0)
      {
            delay(10);
            if(k1==0)
         {
                     f_an1();
            }
      }
      if(k2==0)
      {
            delay(10);
            if(k2==0)
            {
                     f_an2();
            }
      }
      if(k3==0)
      {
         delay(10);
         if(k3==0)
         {
                  f_an3();
         }
      }

      if(sg==0)
      {
            delay(10);
            if(sg==0)
            {
               sgan1();
            }
      }
}
      return 0;
}

void time0() interrupt 1 using 1
{
   int_time ++;       //每來一次中斷,中斷次數int_time自加1
if(int_time==20) //夠20次中斷,即1秒鐘進行一次檢測結果采樣
   {
      int_time=0; //中斷次數清0
      second++; //秒加1
   }
TH0=-50000/256; //50000  =50ms中斷一次
TL0=-50000%256;
t++;
tt++;
}

全部資料51hei下載地址：

洗衣機protues仿真程序 51單片機洗衣機設計 洗衣機程序仿真代碼.rar (157.75 KB, 下載次數: 229)

作者: 萬古琴 時間: 2019-8-24 20:16
未見數碼管亮電機轉動？

作者: 鵬博士PBs 時間: 2019-8-25 07:12
沒太明白什么意思

作者: taotie 時間: 2019-8-25 08:55
全靠水位來控制

作者: taotie 時間: 2019-8-25 09:05

萬古琴發表于 2019-8-24 20:16
未見數碼管亮電機轉動？

調整水位與進水傳感器后自動順序執行~~

作者: 南笙花落 時間: 2020-4-18 19:02
l298芯片電源處加電容是作何種保護�。�

作者: minder灬 時間: 2020-4-24 21:50
數碼管代碼有問題

作者: ileile 時間: 2020-6-9 18:16
請問壓縮包里有protues仿真文件嗎？

作者: 太陽大無敵 時間: 2021-3-15 10:19
可以向你討論一下你的洗衣機設計？

歡迎光臨 (http://www.torrancerestoration.com/bbs/)