標題: Arduino esp8266 blinker溫濕度監控源碼 [打印本頁]

---

作者: hwufo263    時間: 2020-5-7 12:25
標題: Arduino esp8266 blinker溫濕度監控源碼
遠程溫濕度監控，blinker遠程監控，arduino源碼

1. #define BLINKER_WIFI
   
2. 
   
3. #include <Blinker.h>
   
4. #include <DHT.h>
   
5. 
   
6. char auth[] = "20ce32208396"; //上一步中在app中獲取到的Secret Key（新建設備的秘鑰）
   
7. 
   
8. char ssid[] = "PIG"; //你的WiFi熱點名稱
   
9. 
   
10. char pswd[] = "Zq128hw923"; //你的WiFi密碼
    
11. 
    
12. BlinkerNumber HUMI("humi");
    
13. BlinkerNumber TEMP("temp");
    
14. 
    
15. #define DHTPIN 5  //溫濕度接的是GPIO5端口
    
16. #define DHTTYPE DHT11   // DHT 11
    
17. //#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321
    
18. //#define DHTTYPE DHT21   // DHT 21 (AM2301)
    
19. 
    
20. DHT dht(DHTPIN, DHTTYPE);
    
21. 
    
22. float humi_read = 0, temp_read = 0;
    
23. 
    
24. void heartbeat()
    
25. {
    
26.     //反饋溫度數據
    
27.     HUMI.print(humi_read);
    
28.     //設置ui組件圖標和顏色
    
29.     HUMI.icon("fas fa-thermometer-2");
    
30.     HUMI.color("#fddb10");
    
31. 
    
32.     //反饋濕度數據
    
33.     TEMP.print(temp_read);
    
34.     TEMP.icon("fas fa-heart");
    
35.     HUMI.color("#fddb01");
    
36. }
    
37. 
    
38. void dataStorage()
    
39. {
    
40.   Blinker.dataStorage("temp",temp_read);
    
41.   Blinker.dataStorage("humi",humi_read);
    
42. }
    
43. 
    
44. void setup()
    
45. {
    
46.     Serial.begin(115200);
    
47.     pinMode(PIR_sensor,INPUT);
    
48.     BLINKER_DEBUG.stream(Serial);
    
49.     BLINKER_DEBUG.debugAll();
    
50.     pinMode(LED_BUILTIN, OUTPUT);
    
51.     digitalWrite(LED_BUILTIN, LOW);
    
52. 
    
53.     Blinker.begin(auth, ssid, pswd);
    
54.     Blinker.attachHeartbeat(heartbeat);
    
55.     Blinker.attachDataStorage(dataStorage);
    
56.     dht.begin();
    
57. }
    
58. 
    
59. void loop()
    
60. {
    
61.     Blinker.run();
    
62.     float h = dht.readHumidity();
    
63.     float t = dht.readTemperature();
    
64.    
    
65.     if (isnan(h) || isnan(t))
    
66.     {
    
67.         BLINKER_LOG("Failed to read from DHT sensor!");
    
68.     }
    
69.     else
    
70.     {
    
71.         BLINKER_LOG("Humidity: ", h, " %");
    
72.         BLINKER_LOG("Temperature: ", t, " *C");
    
73.         humi_read = h;
    
74.         temp_read = t;
    
75.     }
    
76.     if (t > 20)
    
77.     {
    
78.         Blinker.wechat("Title:機房溫度","state:temperature high" ,"Message:機房溫度過高");
    
79.         Blinker.sms("機房溫度過高！");
    
80.     }
    
81.     Blinker.delay(2000);
    
82. }
    

復制代碼

---

作者: admin    時間: 2020-5-7 16:15
本帖需要重新編輯補全電路原理圖,源碼,詳細說明與圖片即可獲得100+黑幣(帖子下方有編輯按鈕)

---

作者: zhuhaichao11    時間: 2020-5-10 21:59
謝謝分享

---

作者: laoguang    時間: 2020-5-11 00:23
值得學習

---

作者: XXXYYYJJJ    時間: 2020-6-3 15:16
這個需要app嗎？

---

歡迎光臨 (http://www.torrancerestoration.com/bbs/)

Powered by Discuz! X3.1