国产精品香港三级国产av,亚洲欧美制服另类国产无毒

/******定義頭文件**************/
#include<reg52.h>
#include <INTRINS.H>
#include"lcd.h"
#include "ds1302.h"
/******類型重定義*************/
typedef unsigned char uchar;
typedef unsigned int uint;
/******引腳定義***************/
sbit key_1 = P1^0; //定義4個按鍵
sbit key_2 = P1^1;
sbit key_3 = P1^2;
sbit key_4 = P1^3;
sbit key_5=P3^0;//手動/自動模式切換
sbit key_6=P3^1;//手動模式路燈開關
sbit led_1 = P1^4;
sbit Beep = P2^3; //定義聲光報警
sbit AD_clk = P3^4; //定義ADC0832
sbit AD_do = P3^5;
sbit AD_di = P3^5;
sbit AD_cs = P3^6;
sbit red_sr = P3^7; //紅外檢測
/******定義變量***************/
char hour,min,sec; //定義小時、分鐘、秒變量
char time;
char work_time_Start = 16,work_time_End = 5; //設定起始、結束時間
bit light_flag;
uchar light; //定義光照強度
uchar light_limit; //定義光照閾值
uchar Data;
/******聲明函數***************/
void delayms(unsigned int x); //延時函數
void display(); //顯示
void Read_time();
void set_work_time(); //設定工作時間
void set_limit_light(); //設定光照閾值
void work(); //工作狀態
void set_time(); //設定時間
void delay10ms(int d);
void InitTimer0(void); //T0定時器初始化程序
uchar AD(bit Channel); //ADC0832程序
void kongzhi()
{
if(key_6==0)
{
led_1=1;
}
else
{
led_1=0;
}
}
void qiehaun()
{
if(key_5==0)
{
kongzhi();
}
else
{
work();
// if(red_sr==1)
// {
// led_1=1;
// }
// if(red_sr==0)
// {
// led_1=0;
// }
}
}
void main()
{
Beep = led_1 = 0; //聲光報警，LED關閉
InitTimer0(); //T0定時器初始化程序
LcdInit(); //lcd1602初始化
while(1)
{
Ds1302ReadTime(); //讀取時間
set_work_time(); //設定工作時間
set_limit_light(); //設定光照閾值
set_time();
light = AD(0); //讀取ADC0832數值
display(); //顯示
qiehaun();
// work(); //工作狀態
}
}
void Timer0Interrupt(void) interrupt 1
{
static uchar count;
TH0 = 0x0D8;
TL0 = 0x0F0;
count ++;
if(count>=100)
{
time ++;
count = 0;
}
//add your code here
}
/*******************************************************************************
* 函數名 : InitTimer0()
* 函數功能 : T0定時器初始化程序
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void InitTimer0(void)
{
TMOD = 0x01;
TH0 = 0x0D8;
TL0 = 0x0F0;
EA = 0;
ET0 = 1;
TR0 = 1;
}
/*******************************************************************************
* 函數名 : work()
* 函數功能 : 工作狀態
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void work()
{
Read_time(); //轉換時間
if(work_time_End!=0 && work_time_Start!=0) //工作時間已設置
{
if(hour >= work_time_Start) //當前時間大于起始時間，如起始時間為19：00，當前時間為21：00。
{
Data = AD(1);
led_1 = 1; //點亮LED
if(Data < 50) //未檢測到LED點亮
Beep = 1; //聲光報警
else //檢測到Led點亮
Beep = 0; //停止報警
}
else if(hour < work_time_End) //當前時間小于結束時間，如結束時間為06：00，當前時間為04：00。
{
if(red_sr) //檢測到人或車
{
time = 0;
light_flag = 1; //LED標志置1，開始T0定時器計時，點亮LED，10s后LED標志清零，LED熄滅
}
if(light_flag) //LED標志置1，檢測到人或車
{
led_1 = 1; //點亮LED
EA = 1; //開啟中斷
if(time > 10) //10s后
{
light_flag = 0; //LED標志清零
EA = 0; //關中斷
time = 0; //計時清零
}
Data = AD(1);
if(Data < 50) //未檢測到LED點亮
Beep = 1; //聲光報警
else //檢測到Led點亮
Beep = 0; //停止報警
}
else
led_1 = 0;
}
else
{
if(light < light_limit)
{
led_1 = 1;
Data = AD(1);
if(Data < 50) //未檢測到LED點亮
Beep = 1; //聲光報警
else //檢測到Led點亮
Beep = 0; //停止報警
}
else
led_1 = Beep = 0;
}
}
}
/*******************************************************************************
* 函數名 : set_work_time()
* 函數功能 : 設定工作時間
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void set_work_time()
{
if(key_2 == 0) //設置鍵按下
{
delayms(10); //延時消抖
if(key_2 == 0) //再次判斷
{
while(key_2 == 0);
LcdWriteCom(0x01); //清屏
delayms(10);
LcdWriteCom(0x80); //顯示
LcdWriteData('S');
LcdWriteData('E');
LcdWriteData('T');
LcdWriteData('-');
LcdWriteData('w');
LcdWriteData('o');
LcdWriteData('r');
LcdWriteData('k');
LcdWriteData(' ');
LcdWriteData('t');
LcdWriteData('i');
LcdWriteData('m');
LcdWriteData('e');
for(;;) //設定工作時間段
{
LcdWriteCom(0xc0);
LcdWriteData('s');
LcdWriteData('t');
LcdWriteData('a');
LcdWriteData('r');
LcdWriteData('t');
LcdWriteData(':');
LcdWriteCom(0xca);
LcdWriteData(0x30+work_time_Start%100/10);
LcdWriteData(0x30+work_time_Start%10);
if(key_2 == 0) //按鍵2按下，每按一次+5
{
delayms(10);
if(key_2 == 0)
{
while(key_2 == 0);
work_time_Start+=1;
if(work_time_Start > 24)
work_time_Start = 24;
}
}
if(key_3 == 0) //按鍵3按下，每按一次-5
{
delayms(10);
if(key_3 == 0)
{
while(key_3 == 0);
work_time_Start -=1;
if(work_time_Start<=work_time_End) //禁止起始時間小于結束時間
work_time_Start = work_time_End;
}
}
if(key_4 == 0) //按鍵4按下，輸入下一項
{
delayms(10);
if(key_4 == 0)
{
while(key_4 == 0);
LcdWriteCom(0x01);
break;
}
}
}
for(;;) //設定工作時間段
{
LcdWriteCom(0xc0);
LcdWriteData('s');
LcdWriteData('t');
LcdWriteData('o');
LcdWriteData('p');
LcdWriteData(' ');
LcdWriteData(':');
LcdWriteCom(0xca);
LcdWriteData(0x30+work_time_End%100/10);
LcdWriteData(0x30+work_time_End%10);
if(key_2 == 0)
{
delayms(10);
if(key_2 == 0)
{
while(key_2 == 0);
work_time_End += 1;
if(work_time_End > work_time_Start) //禁止結束時間大于開始時間
work_time_End = work_time_Start;
}
}
if(key_3 == 0)
{
delayms(10);
if(key_3 == 0)
{
while(key_3 == 0);
work_time_End -=1;
if(work_time_End < 0)
work_time_End = 0;
}
}
if(key_4 == 0)
{
delayms(10);
if(key_4 == 0)
{
while(key_4 == 0);
LcdWriteCom(0x01);
break;
}
}
}
}
}
}
/*******************************************************************************
* 函數名 : set_limit_light()
* 函數功能 : 設定光照閾值
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void set_limit_light()
{
if(key_3 == 0) //鍵3按下
{
delayms(10); //延時消抖
if(key_3 == 0) //再次判斷
{
while(key_3 == 0);
LcdWriteCom(0x01); //清屏
delayms(10);
LcdWriteCom(0x80); //顯示
LcdWriteData('S');
LcdWriteData('E');
LcdWriteData('T');
LcdWriteData('-');
LcdWriteData('L');
LcdWriteData('i');
LcdWriteData('g');
LcdWriteData('h');
LcdWriteData('t');
LcdWriteData('-');
LcdWriteData('L');
LcdWriteData('i');
LcdWriteData('m');
LcdWriteData('i');
LcdWriteData('t');
for(;;) //設定光照閾值
{
LcdWriteCom(0xc0);
LcdWriteData('D');
LcdWriteData('a');
LcdWriteData('t');
LcdWriteData('a');
LcdWriteData(':');
LcdWriteCom(0xca);
LcdWriteData(0x30+light_limit%1000/100);
LcdWriteData(0x30+light_limit%100/10);
LcdWriteData(0x30+light_limit%10);
if(key_2 == 0) //按鍵2按下，每按一次+5
{
delayms(10);
if(key_2 == 0)
{
while(key_2 == 0);
light_limit += 5;
if(light_limit > 250)
light_limit = 250;
}
}
if(key_3 == 0) //按鍵3按下，每按一次-5
{
delayms(10);
if(key_3 == 0)
{
while(key_3 == 0);
light_limit -= 5;
if(light_limit < 10)
light_limit = 10;
}
}
if(key_4 == 0) //按鍵4按下，輸入下一項
{
delayms(10);
if(key_4 == 0)
{
while(key_4 == 0);
LcdWriteCom(0x01);
break;
}
}
}
}
}
}
/*******************************************************************************
* 函數名 : read_time()
* 函數功能 : 轉換時間
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void Read_time()
{
hour = (Time_1[2]/16)*10 + (Time_1[2]&0x0f);
min = (Time_1[1]/16)*10 + (Time_1[1]&0x0f);
sec = (Time_1[0]/16)*10 + (Time_1[0]&0x0f);
}
/*******************************************************************************
* 函數名 : display()
* 函數功能 : 主界面顯示函數
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void display()
{
LcdWriteCom(0x80);
LcdWriteData('2');
LcdWriteData('0');
LcdWriteData('0'+Time_1[6]/16); //年
LcdWriteData('0'+(Time_1[6]&0x0f));
LcdWriteData('-');
LcdWriteData('0'+Time_1[4]/16); //月
LcdWriteData('0'+(Time_1[4]&0x0f));
LcdWriteData('-');
LcdWriteData('0'+Time_1[3]/16); //日
LcdWriteData('0'+(Time_1[3]&0x0f));
LcdWriteData(' ');
LcdWriteCom(0x8e);
LcdWriteData('0'+time%100/10);
LcdWriteData('0'+time%10);
LcdWriteCom(0xc0);
LcdWriteData('0'+Time_1[2]/16); //時
LcdWriteData('0'+(Time_1[2]&0x0f));
LcdWriteData(':');
LcdWriteData('0'+Time_1[1]/16); //分
LcdWriteData('0'+(Time_1[1]&0x0f));
LcdWriteData(':');
LcdWriteData('0'+Time_1[0]/16); //秒
LcdWriteData('0'+(Time_1[0]&0x0f));
LcdWriteCom(0xcd); //顯示當前光照強度
LcdWriteData('0'+light/100);
LcdWriteData('0'+light%100/10);
LcdWriteData('0'+light%10);
}
/*******************************************************************************
* 函數名 : delayms()
* 函數功能 : 延時函數，ms級別
* 輸入 : 無
* 輸出 : 無
*******************************************************************************/
void delayms(unsigned int x) //0.14ms誤差 0us
{
unsigned char i;
while(x--)
{
for (i = 0; i<13; i++)
{}
}
}
/*************************************************************
* 函數 名 : delay10ms
* 函數功能 : 延時函數，延時時間10ms*d
* 輸入 : 無
* 輸出 : 無
*************************************************************/
void delay10ms(int d) //誤差 0us
{
unsigned char a,b,c;
for(c=d;c>0;c--)
for(b=38;b>0;b--)
for(a=130;a>0;a--);
}
/*************************************************************
* 函數 名 : set_time()
* 函數功能 : 設置時間
* 輸入 : 無
* 輸出 : 無
*************************************************************/
void set_time()
{
char time_flag = 0; //定義一個時間變量
char time_flag_1 = 0;
if(key_1==0) //進入設置時間
{
while(key_1==0);
//設置年
time_flag = Time_1[6]/16; //取出DS1302 年的十位
time_flag_1 = (Time_1[6]&0x0f);
for(;;)
{
LcdWriteCom(0x82); //顯示坐標
LcdWriteCom(0x0e); //光標
delay10ms(50);
LcdWriteCom(0x0c); //光標
if(key_2 ==0)
{
while(key_2==0); //時間加
time_flag++;
}
if(key_3 ==0)
{
while(key_3==0); //時間減
time_flag--;
}
if(time_flag>=9) //顯示范圍
time_flag = 9;
else if(time_flag<=0)
time_flag = 0;
LcdWriteData(time_flag+'0'); //在lcd1602進行顯示
if(key_4 ==0) //確認
{
while(key_4==0); //時間減
Time_1[6] = time_flag*16; //時間寫入數組
break;
}
}
for(;;)
{
LcdWriteCom(0x83); //顯示坐標
LcdWriteCom(0x0e); //光標
delay10ms(50);
LcdWriteCom(0x0c); //光標
if(key_2 ==0)
{
while(key_2==0); //時間加
time_flag_1++;
}
if(key_3 ==0)
{
while(key_3==0); //時間減
time_flag_1--;
}
if(time_flag_1>=9) //顯示范圍
time_flag_1 = 9;
else if(time_flag_1<=0)
time_flag_1 = 0;
LcdWriteData(time_flag_1+'0'); //在lcd1602進行顯示
if(key_4 ==0) //確認
{
while(key_4==0); //時間減
Time_1[6] += time_flag_1; //時間寫入數組
break;
}
}
//設置月
time_flag = Time_1[4]/16; //取出DS1302 月的十位
time_flag_1 = (Time_1[4]&0x0f);
for(;;)
{
LcdWriteCom(0x85); //顯示坐標
LcdWriteCom(0x0e); //光標
delay10ms(50);
LcdWriteCom(0x0c); //光標
if(key_2 ==0)
{
while(key_2==0); //時間加
time_flag++;
}
if(key_3 ==0)
{
while(key_3==0); //時間減
time_flag--;
}
if(time_flag>=9) //顯示范圍
time_flag = 9;
else if(time_flag<=0)
time_flag = 0;
LcdWriteData(time_flag+'0'); //在lcd1602進行顯示
if(key_4 ==0) //確認
{
while(key_4==0); //時間減
Time_1[4] = time_flag*16; //時間寫入數組
break;
}
}
……………………
…………限于本文篇幅余下代碼請從51黑下載附件…………

復制代碼