標題: stm32F407的按鍵FIFO應用 源程序 [打印本頁]
作者: youmeichifan    時間: 2020-7-24 22:23
標題: stm32F407的按鍵FIFO應用 源程序
參考并理解安富萊的代碼，能有按下，彈起和長按，并且長按可以連發，在程序里修改就可以

單片機源程序如下:
  1. /* USER CODE END Header */

  3. /* Includes ------------------------------------------------------------------*/
  4. #include "main.h"
  5. #include "usart.h"
  6. #include "gpio.h"

  8. /* Private includes ----------------------------------------------------------*/
  9. /* USER CODE BEGIN Includes */
  10. #include "KeyFIFO.h"
  11. /* USER CODE END Includes */

  13. /* Private typedef -----------------------------------------------------------*/
  14. /* USER CODE BEGIN PTD */

  16. /* USER CODE END PTD */

  18. /* Private define ------------------------------------------------------------*/
  19. /* USER CODE BEGIN PD */

  21. /* USER CODE END PD */

  23. /* Private macro -------------------------------------------------------------*/
  24. /* USER CODE BEGIN PM */

  26. /* USER CODE END PM */

  28. /* Private variables ---------------------------------------------------------*/

  30. /* USER CODE BEGIN PV */

  32. /* USER CODE END PV */

  34. /* Private function prototypes -----------------------------------------------*/
  35. void SystemClock_Config(void);
  36. /* USER CODE BEGIN PFP */
  37. static void vTimeBaseTask(void);
  38. /* USER CODE END PFP */

  40. /* Private user code ---------------------------------------------------------*/
  41. /* USER CODE BEGIN 0 */

  43. /* USER CODE END 0 */

  45. /**
  46.   * @brief  The application entry point.
  47.   * @retval int
  48.   */
  49. int main(void)
  50. {
  51.   /* USER CODE BEGIN 1 */

  53.   /* USER CODE END 1 */

  55.   /* MCU Configuration--------------------------------------------------------*/

  57.   /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  58.   HAL_Init();

  60.   /* USER CODE BEGIN Init */

  62.   /* USER CODE END Init */

  64.   /* Configure the system clock */
  65.   SystemClock_Config();

  67.   /* USER CODE BEGIN SysInit */

  69.   /* USER CODE END SysInit */

  71.   /* Initialize all configured peripherals */
  72.   MX_GPIO_Init();
  73.   MX_USART1_UART_Init();
  74.   /* USER CODE BEGIN 2 */

  76.   /* USER CODE END 2 */

  78.   /* Infinite loop */
  79.   /* USER CODE BEGIN WHILE */
  80.         bsp_InitKeyVar();
  81.         printf("start\r\n");
  82.   while (1)
  83.   {
  84.                 vTimeBaseTask();
  85.                 ProcessKey();
  86.     /* USER CODE END WHILE */

  88.     /* USER CODE BEGIN 3 */
  89.                
  90.   }
  91.   /* USER CODE END 3 */
  92. }

  94. /**
  95.   * @brief System Clock Configuration
  96.   * @retval None
  97.   */
  98. void SystemClock_Config(void)
  99. {
  100.   RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  101.   RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  103.   /**Configure the main internal regulator output voltage
  104.   */
  105.   __HAL_RCC_PWR_CLK_ENABLE();
  106.   __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
  107.   /**Initializes the CPU, AHB and APB busses clocks
  108.   */
  109.   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  110.   RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  111.   RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  112.   RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  113.   RCC_OscInitStruct.PLL.PLLM = 25;
  114.   RCC_OscInitStruct.PLL.PLLN = 336;
  115.   RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  116.   RCC_OscInitStruct.PLL.PLLQ = 4;
  117.   if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  118.   {
  119.     Error_Handler();
  120.   }
  121.   /**Initializes the CPU, AHB and APB busses clocks
  122.   */
  123.   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
  124.                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  125.   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  126.   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  127.   RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  128.   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;

  130.   if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
  131.   {
  132.     Error_Handler();
  133.   }
  134. }

  136. /* USER CODE BEGIN 4 */
  137. /**********************************************************************************************************
  138. *        函 數 名: HAL_IncTick
  139. *        功能說明: 復寫Systick中斷執行函數
  140. *        形    參: 無
  141. *        返 回 值: 無
  142. **********************************************************************************************************/
  143. void HAL_IncTick(void)
  144. {
  145.         extern __IO uint32_t uwTick;
  146.         extern HAL_TickFreqTypeDef uwTickFreq;
  147.         static uint8_t KeyScanCycle = 0;
  148.        
  149.   uwTick += uwTickFreq;
  150.        
  151.         if(KeyScanCycle++ == KEY_TIMECYCLE)
  152.         {
  153.                 KeyScanCycle = 0;
  154.                 xtFlag.KeyButton = 1;
  155.         }
  156.        
  157. }

  159. /**********************************************************************************************************
  160. *        函 數 名: vTimeBaseTask
  161. *        功能說明: 定時執行的函數，放到主循環里執行
  162. *        形    參: 無
  163. *        返 回 值: 無
  164. **********************************************************************************************************/
  165. static void vTimeBaseTask(void)
  166. {
  167.         if(xtFlag.KeyButton)
  168.         {
  169.                 xtFlag.KeyButton = 0;
  170.                 bsp_KeyScan();
  171.         }
  172. }

  174. /* USER CODE END 4 */

  176. /**
  177.   * @brief  This function is executed in case of error occurrence.
  178.   * @retval None
  179.   */
  180. void Error_Handler(void)
  181. {
  182.   /* USER CODE BEGIN Error_Handler_Debug */
  183.   /* User can add his own implementation to report the HAL error return state */

  185.   /* USER CODE END Error_Handler_Debug */
  186. }

  188. #ifdef  USE_FULL_ASSERT
  189. /**
  190.   * @brief  Reports the name of the source file and the source line number
  191.   *         where the assert_param error has occurred.
  192.   * @param  file: pointer to the source file name
  193.   * @param  line: assert_param error line source number
  194.   * @retval None
  195.   */
  196. void assert_failed(uint8_t *file, uint32_t line)
  197. {
  198.   /* USER CODE BEGIN 6 */
  199.   /* User can add his own implementation to report the file name and line number,
  200.      tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  201.   /* USER CODE END 6 */
  202. }
  203. #endif /* USE_FULL_ASSERT */

  205. /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
復制代碼

所有資料51hei提供下載:
02_KeyFIFO.7z (312.48 KB, 下載次數: 18)





歡迎光臨 (http://www.torrancerestoration.com/bbs/) Powered by Discuz! X3.1