91精品久久久久久窝窝网,精品欧美一区二区精品久久

標題: 關于單片機LCD12232并口驅動程序只有一個瞬間顯示正常? [打印本頁]

作者: 3花木城 時間: 2022-3-27 09:47
標題: 關于單片機LCD12232并口驅動程序只有一個瞬間顯示正常?
圖12是實物
圖345是引腳排列
各種排列都試了一下，有一個瞬間，顯示了程序應該顯示的字符，然后再固定，就不顯示了，所以我能確定，程序是正常的，就是引腳不確定。
下面是清翔的測試程序。有沒有人用過精電蓬遠的屏幕，這屏幕看起來做工很好，能用起來就值了。

/*********************************************************************************
* 【編寫時間】： 2014年3月5日
* 【作者】：清翔電子:03
* 【版本】： 1.0
* 【實驗平臺】： QX-MCS51 單片機開發板
* 【外部晶振】： 11.0592mhz
* 【主控芯片】： STC89C52RC
* 【編譯環境】： Keil μVisio4
* 【程序功能】：漢字液晶顯示程序
* 【使用說明】：使用時請取下J6跳線帽，將本店漢字液晶插入L1排母接口，液晶面向開發板
外部
**********************************************************************************/
#include <reg51.h>

#define uint unsigned int
#define uchar unsigned char
#define xchar unsigned char code

  /*
sbit    A0 = P0^0;
sbit    RRW = P0^1;

sbit    E1 = P0^2;
sbit    E2 = P0^3;

sbit       RST = P0^4;  */
sbit    A0 = P0^0;

sbit    E1 = P0^1;
sbit    E2 = P0^2;

sbit    RRW = P0^3;

sbit       RST = P0^4;

sbit BF_12232 = ACC^7;

xchar picture[]={

/*--  調入了一幅圖像：C:\Users\Administrator\Desktop\未標題-1.bmp  --*/
0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x70,0xF0,0xE0,0xE0,0xC0,0x00,0x00,0x60,0xE0,
0xE3,0xFF,0xFF,0xFF,0xFC,0xF8,0xD0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0xF8,0xF8,0xF0,0xFC,0xFC,0xFC,0xDC,0xC0,
0xC0,0xE0,0xE0,0xE0,0xE0,0xE0,0x70,0x70,0x78,0x38,0xF8,0xF8,0xF0,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0xF0,0xF0,0xF0,0xE0,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0xE0,0xE0,0xE0,0xE0,0xE0,0xE0,0x70,
0xF0,0xF0,0xF0,0xF0,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x38,
0x38,0x38,0xB8,0xF1,0xF1,0xF0,0x70,0xF2,0xFF,0xBF,0xFF,0xFF,0xFF,0xFF,0xFD,0xFD,
0xFC,0xFC,0xDC,0x1C,0x1C,0x1C,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,
0x73,0xF7,0xFF,0xFF,0xFF,0xFB,0xD9,0xC9,0x1D,0x3D,0xF9,0xF1,0xFF,0xFF,0xFF,0xFF,
0x78,0x70,0x60,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x3E,
0xFE,0xFC,0xFC,0xDC,0xFF,0xFF,0xFF,0x7F,0x77,0xA7,0xE7,0xFF,0xFF,0x7F,0x06,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0xC0,
0xC0,0xE0,0xE0,0xE0,0xE0,0xF8,0xFC,0xFC,0xFE,0xFF,0x77,0x73,0x71,0x70,0x70,0xF0,
0xF0,0xF0,0x60,0x00,0x00,0x00,0x00,0x00,0x60,0xF0,0xF8,0xFE,0x3F,0x07,0x01,0x00,
0x00,0xFF,0xFF,0xFF,0xFF,0xDF,0xFF,0xEE,0xEC,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x0E,0x0E,0x8F,0xF7,0xFF,0xFF,0x3F,0x07,0x01,
0x01,0x0D,0x0E,0xEF,0xE7,0xC3,0xFF,0xFF,0xFF,0x1F,0x3E,0x1F,0x0F,0xFF,0xFF,0xFF,
0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x1F,0x1F,0x1D,0xFF,0xFF,
0xFF,0x8E,0x07,0x07,0x0F,0x0F,0x0F,0x00,0x00,0x00,0x00,0xE0,0xF0,0xF0,0x80,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x00,0x00,0x80,0xC0,
0x80,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0F,0x1F,0x1F,0x01,0x01,
0x01,0x10,0x38,0x70,0xFF,0xFF,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x10,0x1C,0x1E,0x1F,0x0F,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,
0x03,0x03,0x03,0x00,0x02,0x07,0x0F,0x1F,0x1F,0x3F,0x1F,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x03,0x07,0x07,0x07,0x07,0x07,
0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x07,0x07,0x01,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

};

xchar hanzi[]={

/*--  文字:  清  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x10,0x60,0x02,0x8C,0x00,0x44,0x54,0x54,0x54,0x7F,0x54,0x54,0x54,0x44,0x40,0x00,
0x04,0x04,0x7E,0x01,0x00,0x00,0xFF,0x15,0x15,0x15,0x55,0x95,0x7F,0x00,0x00,0x00,

/*--  文字:  翔  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x08,0x49,0x4E,0xF8,0x4C,0x4B,0x08,0x12,0x22,0xFE,0x00,0x12,0x22,0xFE,0x00,0x00,
0x82,0x42,0x32,0x0F,0x02,0x02,0x02,0x44,0x82,0x7F,0x04,0x42,0x81,0x7F,0x00,0x00,

/*--  文字:  電  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0xF8,0x88,0x88,0x88,0x88,0xFF,0x88,0x88,0x88,0x88,0xF8,0x00,0x00,0x00,
0x00,0x00,0x1F,0x08,0x08,0x08,0x08,0x7F,0x88,0x88,0x88,0x88,0x9F,0x80,0xF0,0x00,

/*--  文字:  子  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x80,0x82,0x82,0x82,0x82,0x82,0x82,0xE2,0xA2,0x92,0x8A,0x86,0x82,0x80,0x80,0x00,
0x00,0x00,0x00,0x00,0x00,0x40,0x80,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

/*--  文字:  科  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x24,0x24,0xA4,0xFE,0xA3,0x22,0x00,0x22,0xCC,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,
0x08,0x06,0x01,0xFF,0x00,0x01,0x04,0x04,0x04,0x04,0x04,0xFF,0x02,0x02,0x02,0x00,

/*--  文字:  技  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x10,0x10,0x10,0xFF,0x10,0x90,0x08,0x88,0x88,0x88,0xFF,0x88,0x88,0x88,0x08,0x00,
0x04,0x44,0x82,0x7F,0x01,0x80,0x80,0x40,0x43,0x2C,0x10,0x28,0x46,0x81,0x80,0x00,

/*--  文字:  液  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x10,0x60,0x02,0x8C,0x00,0x84,0xE4,0x1C,0x05,0xC6,0xBC,0x24,0x24,0xE4,0x04,0x00,
0x04,0x04,0x7E,0x01,0x00,0x00,0xFF,0x82,0x41,0x26,0x18,0x29,0x46,0x81,0x80,0x00,

/*--  文字:  晶  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x00,0x00,0x7F,0x49,0x49,0x49,0x49,0x49,0x7F,0x00,0x00,0x00,0x00,0x00,
0x00,0xFF,0x49,0x49,0x49,0x49,0xFF,0x00,0xFF,0x49,0x49,0x49,0x49,0xFF,0x00,0x00,

/*--  文字:  測  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x10,0x60,0x02,0x8C,0x00,0xFE,0x02,0xF2,0x02,0xFE,0x00,0xF8,0x00,0xFF,0x00,0x00,
0x04,0x04,0x7E,0x01,0x80,0x47,0x30,0x0F,0x10,0x27,0x00,0x47,0x80,0x7F,0x00,0x00,

/*--  文字:  試  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x40,0x40,0x42,0xCC,0x00,0x90,0x90,0x90,0x90,0x90,0xFF,0x10,0x11,0x16,0x10,0x00,
0x00,0x00,0x00,0x3F,0x10,0x28,0x60,0x3F,0x10,0x10,0x01,0x0E,0x30,0x40,0xF0,0x00,

/*--  文字:  ！  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x33,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

};
//---------------------------------------------
//void delayus(uint us)
//{
//       while(us!=0) us--;
//}
//---------------------------------------------
void delayms(uint ms)
{
      unsigned int x,y;
      for(x=ms;x>0;x--)
            for(y=100;y>0;y--);

}
//-------------------------------------------
void wcomd(uchar c)
{
      A0=0;RRW=0;P3=c;
}
//-------------------------------------------
void wdata(uchar d)
{
      A0=1;RRW=0;P3=d;
}

//-------------------------------------------
void initial()
{
      wcomd(0xaf);E1=0;E2=0;E1=1;E2=1; // Display On
      wcomd(0xc0);E1=0;E2=0;E1=1;E2=1; //Set Display Start Line
      wcomd(0xb8);E1=0;E2=0;E1=1;E2=1; //Set Page-Address
      wcomd(0x4f);E1=0;E2=0;E1=1;E2=1; //Set Column-Address
      wcomd(0xa0);E1=0;E2=0;E1=1;E2=1; //ADC select
      wcomd(0xa4);E1=0;E2=0;E1=1;E2=1; //Static drive off
      wcomd(0xa9);E1=0;E2=0;E1=1;E2=1; //1/32 duty
      wcomd(0xe0);E1=0;E2=0;E1=1;E2=1; //Read modify write mode end
      wcomd(0xee);E1=0;E2=0;E1=1;E2=1; //Release from the read modify write mode
      wcomd(0xe2);E1=0;E2=0;E1=1;E2=1; //Reset line,column,counter register to "0
}
//-------------------------------------------
void disp_bmp(xchar *str)
{
      uint i=0,j=0,k=0;
      uchar temp;

      temp=0xb8;

      wcomd(0xaf);E1=0;delayms(1);E1=1;
      for(k=0;k<4;k++)
      {
            wcomd(temp);E1=0;delayms(1);E1=1;
            wcomd(0x00);E1=0;delayms(1);E1=1;
            wcomd(0xc0);E1=0;delayms(1);E1=1;
            for(i=0;i<61;i++)
            {
                     wdata(str[i+k*122]);E1=0;E1=1;
            }
            temp++;
      }

      temp=0xb8;
      wcomd(0xaf);E2=0;delayms(1);E2=1;
      for(k=0;k<4;k++)
      {
            wcomd(temp);E2=0;delayms(1);E2=1;
            wcomd(0x00);E2=0;delayms(1);E2=1;
            wcomd(0xc0);E2=0;delayms(1);E2=1;
            for(i=0;i<61;i++)
            {
                     wdata(str[61+i+k*122]);E2=0;E2=1;
            }
            temp++;
      }
}

void dis_chinese(uchar x,uchar y,uchar h)
{
      uint i=0;
      if(x<46)                                                                      //能在第一頁完全顯示的條件
      {
            wcomd(0xaf);E1=0;E1=1;
            wcomd(0xb8+y);E1=0;delayms(1);E1=1;
            wcomd(x);E1=0;delayms(1);E1=1;
            wcomd(0xc0);E1=0;delayms(1);E1=1;
            for(i=0;i<16;i++)
            {
                     wdata(hanzi[i+h*32]);E1=0;E1=1;
            }
            wcomd(0xb8+y+1);E1=0;delayms(1);E1=1;
            wcomd(x);E1=0;delayms(1);E1=1;
            wcomd(0xc0);E1=0;delayms(1);E1=1;
            for(i=0;i<16;i++)
            {
                     wdata(hanzi[i+h*32+16]);E1=0;E1=1;
            }
      }
      else if(x>60)                                                             //能在第二頁完全顯示的條件
      {
            wcomd(0xaf);E2=0;E2=1;
            wcomd(0xb8+y);E2=0;delayms(1);E2=1;
            wcomd(x-61);E2=0;delayms(1);E2=1;
            wcomd(0xc0);E2=0;delayms(1);E2=1;
            for(i=0;i<16;i++)
            {
                     wdata(hanzi[i+h*32]);E2=0;E2=1;
            }
            wcomd(0xb8+y+1);E2=0;delayms(1);E2=1;
            wcomd(x-61);E2=0;delayms(1);E2=1;
            wcomd(0xc0);E2=0;delayms(1);E2=1;
            for(i=0;i<16;i++)
            {
                     wdata(hanzi[i+h*32+16]);E2=0;E2=1;
            }
      }
      else                                                                               //拼接顯示                先寫左半部分在第一頁再寫右半部分在第二頁
      {
            wcomd(0xaf);E1=0;E1=1;
            wcomd(0xb8+y);E1=0;delayms(1);E1=1;
            wcomd(x);E1=0;delayms(1);E1=1;
            wcomd(0xc0);E1=0;delayms(1);E1=1;
            for(i=0;i<(61-x);i++)
            {
                     wdata(hanzi[i+h*32]);E1=0;E1=1;
            }
            wcomd(0xb8+y+1);E1=0;delayms(1);E1=1;
            wcomd(x);E1=0;delayms(1);E1=1;
            wcomd(0xc0);E1=0;delayms(1);E1=1;
            for(i=0;i<(61-x);i++)
            {
                     wdata(hanzi[i+h*32+16]);E1=0;E1=1;
            }

            wcomd(0xaf);E2=0;E2=1;
            wcomd(0xb8+y);E2=0;delayms(1);E2=1;
            wcomd(0);E2=0;delayms(1);E2=1;
            wcomd(0xc0);E2=0;delayms(1);E2=1;
            for(i=(61-x);i<16;i++)
            {
                     wdata(hanzi[i+h*32]);E2=0;E2=1;
            }
            wcomd(0xb8+y+1);E2=0;delayms(1);E2=1;
            wcomd(0);E2=0;delayms(1);E2=1;
            wcomd(0xc0);E2=0;delayms(1);E2=1;
            for(i=(61-x);i<16;i++)
            {
                     wdata(hanzi[i+h*32+16]);E2=0;E2=1;
            }
      }
}

void dis_clear()
{
      uint i=0,j=0;

      for(j=0;j<4;j++)
      {
            wcomd(0xb8+j);E1=0;delayms(1);E1=1;
            wcomd(0x00);E1=0;delayms(1);E1=1;
            wcomd(0xc0);E1=0;delayms(1);E1=1;
            for(i=0;i<61;i++)
            {
                     wdata(0x00);E1=0;E1=1;
            }
            wcomd(0xb8+j);E2=0;delayms(1);E2=1;
            wcomd(0x00);E2=0;delayms(1);E2=1;
            wcomd(0xc0);E2=0;delayms(1);E2=1;
            for(i=0;i<61;i++)
            {
                     wdata(0x00);E2=0;E2=1;
            }
      }
}
//-------------------------------------------
/////////////// MAIN //////////////////////
/////////////////////////////////////////////
void main(void)
{
      RST=0;
      delayms(10);
      RST=1;
      delayms(2);
      initial();
      dis_clear();
      dis_clear();
      while(1)
      {
//  A0 = 1;
//RST=0;
//RST = 1;
            //dis_chinese(0,0,0);
            dis_chinese(15,0,0);//清
            dis_chinese(30,0,1);//翔
            dis_chinese(45,0,2);//電
            dis_chinese(60,0,3);//子
            dis_chinese(75,0,4);//科
            dis_chinese(90,0,5);//技

            dis_chinese(43,2,6);//液
            dis_chinese(58,2,7);//晶
            dis_chinese(73,2,8);//測
            dis_chinese(88,2,9);//試
            dis_chinese(103,2,10);//！
//測試屏幕組合顯示
            delayms(5000);

            disp_bmp(picture);

            delayms(8000);
            dis_clear();
            delayms(100);
      }
}

8ef1eed4fcc539fc799a36f1a85130a.jpg (343.48 KB, 下載次數: 72)

95a4d570e6c0d5865a2150f1b6b68eb.jpg (345.63 KB, 下載次數: 49)

作者: heicad 時間: 2022-3-27 17:59
頂一下

作者: man1234567 時間: 2022-3-27 22:11
找店家要個DEMO就好

作者: xjx51 時間: 2022-3-30 19:53
我是頭一次見液晶驅動IC沒用牛屎堆的，這商家可真良心

作者: 3花木城 時間: 2022-3-30 20:19

xjx51 發表于 2022-3-30 19:53
我是頭一次見液晶驅動IC沒用牛屎堆的，這商家可真良心

這屏上有個絲印寫的是2001 ，如果2001是生產日期的話，這屏有20歲了

作者: 3花木城 時間: 2022-3-30 20:22
用萬用表量了現個IC，能確定6，7引腳是E1,E2，因為這兩個引腳一個接IC1,IC2不通，另一個相反。DB0到DB7基本也能確定，兩個IC到引腳上的排列順序。
其實屏不值錢，是別人送的，但是就是驅動不起來，不舒服。

歡迎光臨 (http://www.torrancerestoration.com/bbs/)