標題: STM32利用STM32CUBEMX調用HAL庫實現LED翻轉 [打印本頁]
作者: erevn38107    時間: 2023-3-20 01:51
標題: STM32利用STM32CUBEMX調用HAL庫實現LED翻轉
學習單片機的第一項都是點燈，而STM公司提供了一套軟件可以直接生成代碼模板，利用代碼模板添加自己的代碼調庫即可完成項目。故學習之。只做學習分享用途。
作用：利用HAL函數實現LED狀態翻轉

單片機源程序如下:
  1. #include "main.h"
  2. #include "gpio.h"


  5. void SystemClock_Config(void);
  6. /* USER CODE BEGIN PFP */

  8. /* USER CODE END PFP */

  10. /* Private user code ---------------------------------------------------------*/
  11. /* USER CODE BEGIN 0 */

  13. /* USER CODE END 0 */

  15. /**
  16.   * @brief  The application entry point.
  17.   * @retval int
  18.   */
  19. int main(void)
  20. {
  21.   /* USER CODE BEGIN 1 */

  23.   /* USER CODE END 1 */

  25.   /* MCU Configuration--------------------------------------------------------*/

  27.   /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  28.   HAL_Init();

  30.   /* USER CODE BEGIN Init */

  32.   /* USER CODE END Init */

  34.   /* Configure the system clock */
  35.   SystemClock_Config();

  37.   /* USER CODE BEGIN SysInit */

  39.   /* USER CODE END SysInit */

  41.   /* Initialize all configured peripherals */
  42.   MX_GPIO_Init();
  43.   /* USER CODE BEGIN 2 */

  45.   /* USER CODE END 2 */

  47.   /* Infinite loop */
  48.   /* USER CODE BEGIN WHILE */
  49.   while (1)
  50.   {
  51.     /* USER CODE END WHILE */
  52.     /* USER CODE BEGIN 3 */
  53.                 HAL_GPIO_TogglePin(LED0_GPIO_Port, LED0_Pin);
  54.                 HAL_Delay(1000);
  55.                 HAL_GPIO_TogglePin(LED0_GPIO_Port, LED0_Pin);
  56.                 HAL_GPIO_TogglePin(LED1_GPIO_Port, LED1_Pin);
  57.                 HAL_Delay(1000);
  58.                 HAL_GPIO_TogglePin(LED1_GPIO_Port, LED1_Pin);
  59.                 HAL_GPIO_TogglePin(LED2_GPIO_Port, LED2_Pin);
  60.                 HAL_Delay(1000);
  61.                 HAL_GPIO_TogglePin(LED2_GPIO_Port, LED2_Pin);
  62.   }
  63.   /* USER CODE END 3 */
  64. }

  66. /**
  67.   * @brief System Clock Configuration
  68.   * @retval None
  69.   */
  70. void SystemClock_Config(void)
  71. {
  72.   RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  73.   RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  75.   /** Initializes the RCC Oscillators according to the specified parameters
  76.   * in the RCC_OscInitTypeDef structure.
  77.   */
  78.   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  79.   RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  80.   RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
  81.   RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  82.   RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  83.   RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  84.   RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
  85.   if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  86.   {
  87.     Error_Handler();
  88.   }

  90.   /** Initializes the CPU, AHB and APB buses clocks
  91.   */
  92.   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
  93.                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  94.   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  95.   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  96.   RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  97.   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  99.   if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
  100.   {
  101.     Error_Handler();
  102.   }
  103. }

  105. /* USER CODE BEGIN 4 */

  107. /* USER CODE END 4 */

  109. /**
  110.   * @brief  This function is executed in case of error occurrence.
  111.   * @retval None
  112.   */
  113. void Error_Handler(void)
  114. {
  115.   /* USER CODE BEGIN Error_Handler_Debug */
  116.   /* User can add his own implementation to report the HAL error return state */
  117.   __disable_irq();
  118.   while (1)
  119.   {
  120.   }
  121.   /* USER CODE END Error_Handler_Debug */
  122. }

  124. #ifdef  USE_FULL_ASSERT
  125. /**
  126.   * @brief  Reports the name of the source file and the source line number
  127.   *         where the assert_param error has occurred.
  128.   * @param  file: pointer to the source file name
  129.   * @param  line: assert_param error line source number
  130.   * @retval None
  131.   */
  132. void assert_failed(uint8_t *file, uint32_t line)
  133. {
  134.   /* USER CODE BEGIN 6 */
  135.   /* User can add his own implementation to report the file name and line number,
  136.      ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  137.   /* USER CODE END 6 */
  138. }
  139. #endif /* USE_FULL_ASSERT */
復制代碼

Keil代碼下載:
代碼.7z (267.48 KB, 下載次數: 11)


作者: li64331218    時間: 2023-3-20 11:23
用的哪家的開發板？
作者: erevn38107    時間: 2023-6-9 17:45
li64331218 發表于 2023-3-20 11:23
用的哪家的開發板？

都行，最小系統也可以



歡迎光臨 (http://www.torrancerestoration.com/bbs/) Powered by Discuz! X3.1