亚洲午夜理论一区二区,免费的黄漫画永久观看网站

標題: 求助stc8051U 定時器t0不工作，pwm也沒工作 [打印本頁]

作者: mhb7231 時間: 2025-1-24 11:23
標題: 求助stc8051U 定時器t0不工作，pwm也沒工作
/*根據電池容量的mAh，可以計算電池的持續放電時間的電流數去確定電池的容量。
以下用了一個STC12C5608AD去做檢測電池放電400mA的時間，再以公式400mA*時間=mAh
*/
#include "stc8051U.h"
#include "intrins.h"
#define uchar unsigned char
#define uint unsigned int
#define ulong unsigned long
#define ADCTIM  (*(unsigned char volatile xdata *)0xfea8)
#define VREFH_ADDR CHIPID7
#define VREFL_ADDR CHIPID8
uint BGV;                                     //內部1.19V參考信號源值存放在idata中

typedef unsigned char BYTE;
uchar time1,time2,time3,pwm1;
uint fen=0,ad1=138,ad0;
sbit LED = P3^6;  //背光腳H亮
sbit rw = P2^5;
sbit  rs = P2^6;  //
sbit  en = P2^7;  //
sbit cs1 = P3^2;
sbit cs2 = P3^3;
sbit rst = P3^4;
sbit SPK = P3^5;  //蜂鳴器
sbit POW = P3^7;  //PWM
void InitADC();
uint GetADCResult(BYTE ch);
void Delayus(uint us);
void Delay(uchar  ms);
void lcdstate();
void write_command(uchar  command);
void write_data(uchar  datas);
void lcdinit();
void clearScreen();
void init();
void Timer0Init(void);
void dyADC();
void hz_display16(unsigned char pag, unsigned char col, unsigned char code *hzk);
unsigned char code SZ[][16]=
{/*--  文字:  0  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xF0,0x08,0x08,0x18,0xE0,0x00,0x00,0x00,0x0F,0x10,0x20,0x10,0x0F,0x00,

/*--  文字:  1  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x10,0x00,0x00,0x00,

/*--  文字:  2  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x30,0x08,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x18,0x14,0x13,0x10,0x08,0x00,

/*--  文字:  3  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x10,0x08,0x88,0x78,0x00,0x00,0x00,0x00,0x10,0x20,0x20,0x11,0x0E,0x00,

/*--  文字:  4  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1F,0x02,0x00,

/*--  文字:  5  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x70,0x48,0xC8,0x88,0x00,0x00,0x00,0x10,0x10,0x20,0x10,0x0F,0x00,0x00,

/*--  文字:  6  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xE0,0x90,0x88,0x80,0x00,0x00,0x00,0x07,0x18,0x20,0x20,0x19,0x06,0x00,

/*--  文字:  7  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x10,0x08,0x08,0x88,0x78,0x00,0x00,0x00,0x00,0x00,0x18,0x07,0x00,0x00,0x00,

/*--  文字:  8  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x78,0x88,0x88,0x78,0x00,0x00,0x00,0x0C,0x12,0x21,0x21,0x1E,0x00,0x00,

/*--  文字:  9  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x60,0x98,0x08,0x08,0xF8,0xC0,0x00,0x00,0x00,0x21,0x12,0x09,0x07,0x00,0x00,

/*--  文字:  :  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0xC,0xC,0x00,0x00,0x00,0x00,0x00,
/*--  文字:  B  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,
/*--  文字:  a  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,
/*--  文字:  t  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,

/*--  文字:  T  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,

/*--  文字:  i  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,

/*--  文字:  m  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,

/*--  文字:  e  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,
/*--  文字:  V  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,

/*--  文字:  A  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,

/*--  文字:  h  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,
/*--  文字:  一  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x0,0x0,0x0,0x0,0x00,0x00,0x00,0x20,0x20,0x20,0x20,0x20,0x20,0x00,
/*--  文字: .  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x0,0x0,0x00,0x00,0x00,0x00,0x00,0x00,0xC,0x0,0x00,0x00,0x00,0x00,0x00,
};
/*----------------------------
讀取ADC結果
----------------------------*/
uint GetADCResult(BYTE channel)
{
ADC_RES = 0;
ADC_RESL = 0;

  ADC_CONTR = (ADC_CONTR & 0xF0) | 0x40 | channel; //啟動 AD 轉換
_nop_();                      //等待4個NOP
_nop_();
_nop_();
_nop_();
while (!(ADC_CONTR & 0x20));             //查詢ADC完成標志
ADC_CONTR &= ~0x20;
      return (((int)ADC_RES << 8) | ADC_RESL);       //adc_data*4的意思是左移兩位，4 = 2的2次方。
                                 //然后左移后加上adc_low的值，這個值應該是adc轉換的低兩位。

}

/*----------------------------
初始化ADC
----------------------------*/
void InitADC()
{
P_SW2 |= 0x80;                //擴展 RAM 區特殊功能寄存器（XFR）訪問控制寄存器
ADCTIM = 0x3f;                            //ADC時序控制寄存器3f=00111111
P_SW2 &= 0x7f;

ADCCFG = 0x2f;                            //設置ADC時鐘為系統時鐘/2/16
ADC_CONTR = 0x80;                         //使能ADC模塊,并選擇第15通道 8f=10001111                      //ADC上電并延時
}
void lcdstate()  //讀狀態指令
{
uchar  lcd=0x00; /*設置初值為0，全部為低，方便后面的判忙*/
rs=0; /*根據時序圖拉低，選擇寫指令*/
rw=1; /*根據時序圖拉低，選擇寫模式*/
do
{
en=1; /*使能，使液晶輸出信號，檢查是否忙*/
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
lcd=P0; /*把P0口的狀態值讀回來給lcd*/
en=0; /*使能端跳變*/;
}while(lcd&0x80); /*結果的高位保留，如果高位DB7為一，則表示忙*/
}
void Delayus(uint us)             //@12.000MHz
{
while(--us)
{
            _nop_();
            _nop_();
            _nop_();
            _nop_();
}
}

void delay(uchar  ms)
{ uchar i;
uchar j;
  for(i=0;i<100;i++)
for(j=0;j<ms;j++);
}
void write_command(uchar command)
{
lcdstate();
  rs=0;                               //RS=0;為往MCU進行指令操作
  rw=0;                               //RW=0;為往MCU寫入操作
  en=0;
  _nop_();_nop_();_nop_();_nop_();/*延時4US*/
  en=1;
  _nop_();_nop_();_nop_();_nop_();/*延時4US*/
  P0=command;
  _nop_();_nop_();_nop_();_nop_();/*延時4US*/
  en=0;
}
void write_data(uchar datas)
{
lcdstate();
rs=1;
rw=0;
en=0;
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
en=1;
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
P0=datas;
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
en=0;
}
void lcdinit()
{
delay(100);                                        //
cs1=1;
      cs2=1;
      delay(100);
      lcdstate();                               //
      write_command(0x3e);                //
      write_command(0xb8+0);                      //
      write_command(0xc0+0);                //
      write_command(0x40+0);                //
      write_command(0x3f);
}
void clearScreen(  )
{ uchar i,j;
lcdstate();
cs1=1;
      cs2=1;
      write_command(0x3f);                      //設置顯示開
      write_command(0xb8);                   //Y       設置第0頁；
      write_command(0x40);                      //       設置第0列
for(i=0;i<8;i++)
{
   write_command(0xb8+i);
   for(j=0;j<64;j++)
   {
         //write_command(0x40+j);
   write_data(0x00);

   }
}
}

void Timer0Init(void)             //2毫秒@12.000MHz
{
      AUXR &= 0x7F;             //定時器時鐘12T模式
      TMOD &= 0xF0;             //設置定時器模式
      TMOD |= 0x01;             //設置定時器模式
      TL0 = 0x30;             //設置定時初值
      TH0 = 0xF8;             //設置定時初值
      TF0 = 0;             //清除TF0標志
      TR0 = 0;             //定時器0開始計時
}

void Timer1Init(void)             //5毫秒@12.000MHz
{
      AUXR &= 0xBF;             //定時器時鐘12T模式
      TMOD &= 0x0F;             //設置定時器模式
      TMOD |= 0x10;             //設置定時器模式
      TL1 = 0x78;             //設置定時初值
      TH1 = 0xEC;             //設置定時初值
      TF1 = 0;             //清除TF1標志
      TR1 = 1;             //定時器1開始計時
}
void hz_display8(unsigned char pag, unsigned char col, unsigned char  zi)
{
      uchar j=0;
      uchar i=0;
      for(j=0;j<2;j++)                         //這里寫四頁
      {
            write_command(0xb8+pag+j);       //page在這里就是從page表示的這頁開始寫起。
            write_command(0x40+col);       //從列為col表示的列開始
            for(i=0;i<8;i++)                         //這里寫32列
            write_data(SZ[zi][8*j+i]);       //J為頁，I，為第J行第I個數
      }
}
void dyADC()
{
int res,ad1;
int xes;
GetADCResult(15);
GetADCResult(15);
res=GetADCResult(15);//讀內部基準ADC, 讀15通道
GetADCResult(0);
GetADCResult(0);
xes=GetADCResult(0);//讀p1.1外部電壓ADC
ad1=(int)((long)xes* BGV / res);  //計算p5.5外部電壓, vcc為1.19V,
ad0=ad1/10;

}
void main()
{
bit q1=0,q2=0,q3=0;
uchar k1;
ulong ww=1667;
P_SW2 = 0X80; //使能訪問 XFR,沒有沖突不用關閉
CKCON = 0x00; //設置外部數據總線速度為最快
WTST = 0x00;
P0M0 = 0x00;    //00上拉準雙向口/10浮空輸入
P0M1 = 0x00;    //11開漏輸出/01推挽輸出
P1M0 = 0x00;
P1M1 = 0x01; //設置P1.0為ADC
P2M0 = 0x00;
P2M1 = 0x00;
P3M0 = 0x00;    //00上拉準雙向口/10浮空輸入
P3M1 = 0x00;    //11開漏輸出/01推挽輸出
P4M0 = 0x00;
P4M1 = 0x00;
P5M0 = 0x00;
P5M1 = 0x00;
BGV = (VREFH_ADDR << 8) + VREFL_ADDR; //從 CHIPID 中讀取內部參考電壓值
      POW=0;
      SPK=0;
   lcdinit();
   clearScreen();
      InitADC();
      Timer0Init();
      Timer1Init();
      TR0 = 1;                      //timer0 start running
ET0 = 1;                      //enable timer0 interrupt
// TR1 = 1;                      //timer1 start running
// ET1 = 1;                      //enable timer1 interrupt
EA = 1;                      //open global interrupt switch

      for(k1=255;k1>0;k1--)
         {
               SPK=~SPK;
            Delayus(k1);
         }
         SPK=0;

cs1=1;
cs2=0;
hz_display8(0,0,11); //Batt:
hz_display8(0,8,12);
hz_display8(0,16,13);
hz_display8(0,24,13);
hz_display8(0,32,10);
hz_display8(6,0,14);  //time:
hz_display8(6,8,15);
hz_display8(6,16,16);
hz_display8(6,24,17);
hz_display8(6,32,10);

      while(1)
{

if(EA==1)
   {
   cs1=1;
      cs2=0;
      hz_display8(6,40,(time3%100/10));  //時
      hz_display8(6,48,(time3%10/1));
      hz_display8(6,56,10);  //：
   cs1=0;
      cs2=1;
      hz_display8(6,0,(time2%100/10));  //分
      hz_display8(6,8,(time2%10/1));
      hz_display8(6,16,10);  //：
      hz_display8(6,24,(time1%100/10));  //秒
      hz_display8(6,32,(time1%10/1));
   }

      if(q1==0&time1==2)
         {
            dyADC();
            cs1=1;
            cs2=0;
            hz_display8(0,40,(ad0/100));
            hz_display8(0,48,22);
            hz_display8(0,56,(ad0%100/10));
            cs1=0;
            cs2=1;
            hz_display8(0,0,(ad0%10));
            hz_display8(0,8,18);  //v

            q1=1;

            for(k1=0;k1<255;k1++)
               {
                  SPK=~SPK;
                  Delayus(150);
               }
                     Delay(100);
            for(k1=0;k1<255;k1++)
               {
                  SPK=~SPK;
                  Delayus(150);
               }
                  SPK=0;
                  CCON = 0;                      //PCA控制寄存器CCON
                                                            //PCA timer stop running
                                                            //Clear CF flag
                                                            //Clear all module interrupt flag
                  CL = 0;                      //PCA的16位計數器 — 低8位CL和高8位CH
                  CH = 0;
                  CMOD = 0x08;                   //工作模式寄存器CMOD
                                                            //Disable PCA timer overflow interrupt
                  CCAP1H = CCAP1L = 0xFF;       //模塊0的捕捉/比較寄存器用來控制輸出的占?比
                  CCAPM1 = 0x42;                //PCA比較/捕獲寄存器CCAPMn (n=0,1,2,3) PCA interrupt
                  PCA_PWM1 = 0x40;
                  CCON |= CR;                      //PCA計數器陣列，運行控制位
                  TR1 = 1;
                  ET1 = 1;
            }
      dyADC();
         cs1=0;
         cs2=1;
         hz_display8(0,16,(ad0/100));
         hz_display8(0,24,22);
         hz_display8(0,32,(ad0%100/10));
         hz_display8(0,40,(ad0%10));
         hz_display8(0,48,18);  //v

         if(fen>=1)LED=0;
         if(ad0<=286)q3=1;
            while(q3==1)
               {
                  for(k1=0;k1<100;k1++)
                     {
                        SPK=~SPK;
                        Delayus(110);
                     }
               SPK=0;
               LED=~LED;
               CCAP1H = CCAP1L = 0xFF;
               POW=0;
               EA=0;
               Delay(500);
            dyADC();
               //  ad0=GetADCResult(0);
         cs1=0;
                  cs2=1;
      hz_display8(0,16,(ad0%1000/100));
      hz_display8(0,24,10);
      hz_display8(0,16,(ad0%100/10));
      hz_display8(0,16,(ad0%10/1));
      hz_display8(0,24,18);  //v

                  if(!q2)
                  {
                     ww*=fen;
                     ww*=4;
                       cs1=1;
                     cs2=2;
                     hz_display8(6,0,21);  //-------
                     hz_display8(6,8,21);
hz_display8(6,16,21);
hz_display8(6,24,21);
hz_display8(6,32,21);
hz_display8(6,40,21);
hz_display8(6,48,21);
hz_display8(6,56,21);
   cs1=0;
      cs2=1;
   hz_display8(6,0,(ww%100000000/10000000));
            hz_display8(6,8,(ww%10000000/1000000));
            hz_display8(6,16,(ww%1000000/100000));
            hz_display8(6,24,(ww%100000/10000));
            hz_display8(6,32,(ww%10000/1000));
            hz_display8(6,40,16);  //mah
            hz_display8(6,48,19);
            hz_display8(6,56,20);
                  Delay(1000);
                  q2=1;
                        }
                        }

}

}
void tm0_isr() interrupt 1 using 1
{
  static uchar i1,i2;
      TL0 = 0x30;             //設置定時初值
      TH0 = 0xF8;             //設置定時初值
      i1++;
  if(i1>=50)
  {
i1=0;
i2++;
if(i2>=10)
         {
         i2=0;
         time1++;
         if(time1>=60)
               {
                  time1=0;
                  time2++;
                  fen++;
   if(time2>=60)
         {
            time2=0;
               time3++;
               if(time3>=24)time3=0;
         }
                  }
                  }
  }
  // ad0=GetADCResult(0);
}

void tm1_isr() interrupt 3 using 1
{
      TL1 = 0x78;             //設置定時初值
      TH1 = 0xEC;             //設置定時初值

      if(ad0>=428)CCAP1H = CCAP1L = 142; //模塊0的捕捉/比較寄存器用來控制輸出的占?比
      if(ad0<=427&&ad0>424)CCAP1H = CCAP1L = 142;
      if(ad0<=424&&ad0>420)CCAP1H = CCAP1L = 141;
      if(ad0<=420&&ad0>416)CCAP1H = CCAP1L = 140;
      if(ad0<=416&&ad0>412)CCAP1H = CCAP1L = 139;
      if(ad0<=412&&ad0>408)CCAP1H = CCAP1L = 138;
      if(ad0<=408&&ad0>404)CCAP1H = CCAP1L = 137;
      if(ad0<=404&&ad0>400)CCAP1H = CCAP1L = 136;
      if(ad0<=400&&ad0>396)CCAP1H = CCAP1L = 135;
      if(ad0<=396&&ad0>392)CCAP1H = CCAP1L = 134;
      if(ad0<=392&&ad0>388)CCAP1H = CCAP1L = 132;//
      if(ad0<=388&&ad0>384)CCAP1H = CCAP1L = 131;
      if(ad0<=384&&ad0>380)CCAP1H = CCAP1L = 129;
      if(ad0<=380&&ad0>376)CCAP1H = CCAP1L = 128;
      if(ad0<=376&&ad0>372)CCAP1H = CCAP1L = 127;
      if(ad0<=372&&ad0>368)CCAP1H = CCAP1L = 126;//
      if(ad0<=368&&ad0>364)CCAP1H = CCAP1L = 125;
      if(ad0<=364&&ad0>360)CCAP1H = CCAP1L = 123;
      if(ad0<=360&&ad0>356)CCAP1H = CCAP1L = 122;
      if(ad0<=356&&ad0>352)CCAP1H = CCAP1L = 120;
      if(ad0<=352&&ad0>348)CCAP1H = CCAP1L = 119;
      if(ad0<=348&&ad0>344)CCAP1H = CCAP1L = 117;
      if(ad0<=344&&ad0>340)CCAP1H = CCAP1L = 116;
      if(ad0<=340&&ad0>336)CCAP1H = CCAP1L = 114;
      if(ad0<=336&&ad0>332)CCAP1H = CCAP1L = 113;
      if(ad0<=332&&ad0>328)CCAP1H = CCAP1L = 111;
      if(ad0<=328&&ad0>324)CCAP1H = CCAP1L = 109;
      if(ad0<=324&&ad0>320)CCAP1H = CCAP1L = 108;
      if(ad0<=320&&ad0>316)CCAP1H = CCAP1L = 106;
      if(ad0<=316&&ad0>312)CCAP1H = CCAP1L = 105;
      if(ad0<=312&&ad0>308)CCAP1H = CCAP1L = 103;
      if(ad0<=304&&ad0>300)CCAP1H = CCAP1L = 100;
      if(ad0<=300&&ad0>296)CCAP1H = CCAP1L = 98;
      if(ad0<=296&&ad0>292)CCAP1H = CCAP1L = 97;
      if(ad0<=292&&ad0>288)CCAP1H = CCAP1L = 94;
      if(ad0<=288&&ad0>284)CCAP1H = CCAP1L = 91;
      if(ad0<=284)CCAP1H = CCAP1L = 0xFF;

      //CCAPM0 = 0x42;*/
}

作者: lkc8210 時間: 2025-1-26 16:05
LCD有沒有顯示？

作者: mhb7231 時間: 2025-1-27 20:55
/*根據電池容量的mAh，可以計算電池的持續放電時間的電流數去確定電池的容量。
以下用了stc8051U去做檢測電池放電400mA的時間，再以公式400mA*時間=mAh
*/
#include "stc8051U.h"
#include "intrins.h"
#define uchar unsigned char
#define uint unsigned int
#define ulong unsigned long
#define ADCTIM  (*(unsigned char volatile xdata *)0xfea8)
#define VREFH_ADDR CHIPID7
#define VREFL_ADDR CHIPID8
uint BGV;                                     //內部1.19V參考信號源值存放在idata中

typedef unsigned char BYTE;
uchar time1,time2,time3,pwm1;
uint fen=0,ad1=138,ad0;
sbit LED1 = P1^7;
sbit LED = P3^6;  //背光腳H亮
sbit rw = P2^5;
sbit  rs = P2^6;  //
sbit  en = P2^7;  //
sbit cs1 = P3^2;
sbit cs2 = P3^3;
sbit rst = P3^4;
sbit SPK = P3^5;  //蜂鳴器
sbit POW = P3^7;  //PWM
void InitADC();
uint GetADCResult(BYTE ch);
void Delayus(uint us);
void Delay(uchar  ms);
void lcdstate();
void write_command(uchar  command);
void write_data(uchar  datas);
void lcdinit();
void clearScreen();
void init();
void Timer0Init(void);
void Timer1Init(void);
void dyADC();
void hz_display16(unsigned char pag, unsigned char col, unsigned char code *hzk);
unsigned char code SZ[][16]=
{/*--  文字:  0  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xF0,0x08,0x08,0x18,0xE0,0x00,0x00,0x00,0x0F,0x10,0x20,0x10,0x0F,0x00,

/*--  文字:  1  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x10,0x00,0x00,0x00,

/*--  文字:  2  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x30,0x08,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x18,0x14,0x13,0x10,0x08,0x00,

/*--  文字:  3  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x10,0x08,0x88,0x78,0x00,0x00,0x00,0x00,0x10,0x20,0x20,0x11,0x0E,0x00,

/*--  文字:  4  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1F,0x02,0x00,

/*--  文字:  5  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x70,0x48,0xC8,0x88,0x00,0x00,0x00,0x10,0x10,0x20,0x10,0x0F,0x00,0x00,

/*--  文字:  6  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xE0,0x90,0x88,0x80,0x00,0x00,0x00,0x07,0x18,0x20,0x20,0x19,0x06,0x00,

/*--  文字:  7  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x10,0x08,0x08,0x88,0x78,0x00,0x00,0x00,0x00,0x00,0x18,0x07,0x00,0x00,0x00,

/*--  文字:  8  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x78,0x88,0x88,0x78,0x00,0x00,0x00,0x0C,0x12,0x21,0x21,0x1E,0x00,0x00,

/*--  文字:  9  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x60,0x98,0x08,0x08,0xF8,0xC0,0x00,0x00,0x00,0x21,0x12,0x09,0x07,0x00,0x00,

/*--  文字:  :  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0xC,0xC,0x00,0x00,0x00,0x00,0x00,
/*--  文字:  B  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,
/*--  文字:  a  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,
/*--  文字:  t  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,

/*--  文字:  T  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,

/*--  文字:  i  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,

/*--  文字:  m  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,

/*--  文字:  e  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,
/*--  文字:  V  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,

/*--  文字:  A  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,

/*--  文字:  h  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=8x16 --*/
0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,
/*--  文字:  一  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x0,0x0,0x0,0x0,0x00,0x00,0x00,0x20,0x20,0x20,0x20,0x20,0x20,0x00,
/*--  文字: .  --*/
/*--  楷體_GB231212;  此字體下對應的點陣為：寬x高=8x16 --*/
0x00,0x0,0x0,0x00,0x00,0x00,0x00,0x00,0x00,0xC,0x0,0x00,0x00,0x00,0x00,0x00,
};
/*----------------------------
讀取ADC結果
----------------------------*/
uint GetADCResult(BYTE channel)
{
ADC_RES = 0;
ADC_RESL = 0;

  ADC_CONTR = (ADC_CONTR & 0xF0) | 0x40 | channel; //啟動 AD 轉換
_nop_();                      //等待4個NOP
_nop_();
_nop_();
_nop_();
while (!(ADC_CONTR & 0x20));             //查詢ADC完成標志
ADC_CONTR &= ~0x20;
      return (((int)ADC_RES << 8) | ADC_RESL);       //adc_data*4的意思是左移兩位，4 = 2的2次方。
                                 //然后左移后加上adc_low的值，這個值應該是adc轉換的低兩位。

}

/*----------------------------
初始化ADC
----------------------------*/
void InitADC()
{
P_SW2 |= 0x80;                //擴展 RAM 區特殊功能寄存器（XFR）訪問控制寄存器
ADCTIM = 0x3f;                            //ADC時序控制寄存器3f=00111111
P_SW2 &= 0x7f;

ADCCFG = 0x2f;                            //設置ADC時鐘為系統時鐘/2/16
ADC_CONTR = 0x80;                         //使能ADC模塊,并選擇第15通道 8f=10001111                      //ADC上電并延時
}
void lcdstate()  //讀狀態指令
{
uchar  lcd=0x00; /*設置初值為0，全部為低，方便后面的判忙*/
rs=0; /*根據時序圖拉低，選擇寫指令*/
rw=1; /*根據時序圖拉低，選擇寫模式*/
do
{
en=1; /*使能，使液晶輸出信號，檢查是否忙*/
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
lcd=P0; /*把P0口的狀態值讀回來給lcd*/
en=0; /*使能端跳變*/;
}while(lcd&0x80); /*結果的高位保留，如果高位DB7為一，則表示忙*/
}
void Delayus(uint us)             //@12.000MHz
{
while(--us)
{
            _nop_();
            _nop_();
            _nop_();
            _nop_();
}
}

void delay(uchar  ms)
{ uchar i;
uchar j;
  for(i=0;i<100;i++)
for(j=0;j<ms;j++);
}
void write_command(uchar command)
{
lcdstate();
  rs=0;                               //RS=0;為往MCU進行指令操作
  rw=0;                               //RW=0;為往MCU寫入操作
  en=0;
  _nop_();_nop_();_nop_();_nop_();/*延時4US*/
  en=1;
  _nop_();_nop_();_nop_();_nop_();/*延時4US*/
  P0=command;
  _nop_();_nop_();_nop_();_nop_();/*延時4US*/
  en=0;
}
void write_data(uchar datas)
{
lcdstate();
rs=1;
rw=0;
en=0;
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
en=1;
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
P0=datas;
_nop_();_nop_();_nop_();_nop_();/*延時4US*/
en=0;
}
void lcdinit()
{
delay(100);                                        //
cs1=1;
      cs2=1;
      delay(100);
      lcdstate();                               //
      write_command(0x3e);                //
      write_command(0xb8+0);                      //
      write_command(0xc0+0);                //
      write_command(0x40+0);                //
      write_command(0x3f);
}
void clearScreen(  )
{ uchar i,j;
lcdstate();
cs1=1;
      cs2=1;
      write_command(0x3f);                      //設置顯示開
      write_command(0xb8);                   //Y       設置第0頁；
      write_command(0x40);                      //       設置第0列
for(i=0;i<8;i++)
{
   write_command(0xb8+i);
   for(j=0;j<64;j++)
   {
         //write_command(0x40+j);
   write_data(0x00);

   }
}
}

void Timer0Init(void)             //2毫秒@12.000MHz 時間
{
      AUXR &= 0x7F;             //定時器時鐘12T模式
      TMOD &= 0xF0;             //設置定時器模式
      TMOD |= 0x01;             //設置定時器模式
      TL0 = 0x30;             //設置定時初值
      TH0 = 0xF8;             //設置定時初值
      TF0 = 0;             //清除TF0標志
      TR0 = 0;             //定時器0開始計時
}

void Timer1Init(void)             //5毫秒@12.000MHz
{
      AUXR &= 0xBF;             //定時器時鐘12T模式
      TMOD &= 0x0F;             //設置定時器模式
      TMOD |= 0x10;             //設置定時器模式
TL0 = 0xB0; //設置定時初始值
TH0 = 0x3C;                   //設置定時初值
      TF1 = 0;             //清除TF1標志
      TR1 = 0;             //定時器1開始計時
}
void hz_display8(unsigned char pag, unsigned char col, unsigned char  zi)
{
      uchar j=0;
      uchar i=0;
      for(j=0;j<2;j++)                         //這里寫四頁
      {
            write_command(0xb8+pag+j);       //page在這里就是從page表示的這頁開始寫起。
            write_command(0x40+col);       //從列為col表示的列開始
            for(i=0;i<8;i++)                         //這里寫32列
            write_data(SZ[zi][8*j+i]);       //J為頁，I，為第J行第I個數
      }
}
void dyADC()
{
int res,ad1;
int xes;
GetADCResult(15);
GetADCResult(15);
res=GetADCResult(15);//讀內部基準ADC, 讀15通道
GetADCResult(0);
GetADCResult(0);
xes=GetADCResult(0);//讀p1.1外部電壓ADC
ad1=(int)((long)xes* BGV / res);  //計算p1.1外部電壓, vcc為1.19V,
ad0=ad1/10;

}
void main()
{
bit q1=0,q2=0,q3=0;
  //  uchar k1;
ulong ww=1667;
P_SW2 = 0X80; //使能訪問 XFR,沒有沖突不用關閉
CKCON = 0x00; //設置外部數據總線速度為最快
WTST = 0x00;
P0M0 = 0x00;    //00上拉準雙向口/10浮空輸入
P0M1 = 0x00;    //11開漏輸出/01推挽輸出
P1M0 = 0x00;
P1M1 = 0x01; //設置P1.0為ADC
P2M0 = 0x00;
P2M1 = 0x00;
P3M0 = 0x00;    //00上拉準雙向口/10浮空輸入
P3M1 = 0x00;    //11開漏輸出/01推挽輸出
P4M0 = 0x00;
P4M1 = 0x00;
P5M0 = 0x00;
P5M1 = 0x00;
BGV = (VREFH_ADDR << 8) + VREFL_ADDR; //從 CHIPID 中讀取內部參考電壓值
      POW=1;
LED1=1;
      SPK=0;
   lcdinit();
   clearScreen();
      InitADC();
      Timer0Init();
      Timer1Init();
      TR0 = 1;                      //timer0  時間
ET0 = 1;                      // 時間
// TR1 = 1;                      //timer1 start running
// ET1 = 1;                      //enable timer1 interrupt
EA = 1;                      //open global interrupt switch

cs1=1;
cs2=0;
hz_display8(0,0,11); //Batt:
hz_display8(0,8,12);
hz_display8(0,16,13);
hz_display8(0,24,13);
hz_display8(0,32,10);
hz_display8(6,0,14);  //time:
hz_display8(6,8,15);
hz_display8(6,16,16);
hz_display8(6,24,17);
hz_display8(6,32,10);
while(1)
{

      while(1)
{

if(EA==1)
   {
   cs1=1;
      cs2=0;
      hz_display8(6,40,(time3%100/10));  //時
      hz_display8(6,48,(time3%10/1));
      hz_display8(6,56,10);  //：
   cs1=0;
      cs2=1;
      hz_display8(6,0,(time2%100/10));  //分
      hz_display8(6,8,(time2%10/1));
      hz_display8(6,16,10);  //：
      hz_display8(6,24,(time1%100/10));  //秒
      hz_display8(6,32,(time1%10/1));
   }

      if(q1==0&time1==2)  //q1=0 time1=2  才執行括號里的程序
         {
            dyADC();
            cs1=1;
            cs2=0;
            hz_display8(0,40,(ad0/100));
            hz_display8(0,48,22);
            hz_display8(0,56,(ad0%100/10));
            cs1=0;
            cs2=1;
            hz_display8(0,0,(ad0%10));
            hz_display8(0,8,18);  //v

            q1=1;

                  CCON = 0;                      //PCA控制寄存器CCON
                  CMOD = 0x08;                   //工作模式寄存器CMOD
                  CL = 0;                      //PCA的16位計數器 — 低8位CL和高8位CH
                  CH = 0;
                  CCAPM1 = 0x42;                //PCA比較/捕獲寄存器CCAPMn (n=0,1,2,3) PCA interrupt
                  PCA_PWM1 = 0x40;                                                       //Disable PCA timer overflow interrupt
                  CCAP1H = CCAP1L = 0x01;       //模塊0的捕捉/比較寄存器用來控制輸出的占?比
                     CCON |= CR;                      //PCA計數器陣列，運行控制位
                  // while(1);
   TR1 = 1;    // 時間
                  ET1 = 1;
            }
      dyADC();
//ad0=GetADCResult(0);
         cs1=0;
         cs2=1;
         hz_display8(0,16,(ad0/100));
         hz_display8(0,24,22);
         hz_display8(0,32,(ad0%100/10));
         hz_display8(0,40,(ad0%10));
         hz_display8(0,48,18);  //v

         if(fen>=1)LED=0;
         if(ad0<=286)q3=1;
            while(q3==1)
               {

               LED=~LED;
               // CCAP1H = CCAP1L = 0x00;
               POW=0;
               EA=0;
               Delay(500);
Delay(500);
Delay(500);
      Delay(500);
Delay(500);
Delay(500);
   Delay(500);
Delay(500);
Delay(500);
dyADC();
               //  ad0=GetADCResult(0);
         cs1=0;
               cs2=1;
      hz_display8(0,16,(ad0/100));
      hz_display8(0,24,22);
      hz_display8(0,32,(ad0%100/10));
      hz_display8(0,40,(ad0%10));
      hz_display8(0,48,18);  //v

                  if(!q2)
                  {
                     ww*=fen;
                     ww*=4;
                       cs1=1;
                     cs2=2;
                  hz_display8(6,0,21);  //-------
            hz_display8(6,8,21);
hz_display8(6,16,21);
hz_display8(6,24,21);
hz_display8(6,32,21);
hz_display8(6,40,21);
hz_display8(6,48,21);
hz_display8(6,56,21);
   cs1=0;
      cs2=1;
      hz_display8(6,0,(ww%100000000/10000000));
            hz_display8(6,8,(ww%10000000/1000000));
            hz_display8(6,16,(ww%1000000/100000));
            hz_display8(6,24,(ww%100000/10000));
            hz_display8(6,32,(ww%10000/1000));
            hz_display8(6,40,16);  //mah
            hz_display8(6,48,19);
            hz_display8(6,56,20);
                  Delay(1000);
                  q2=1;

                        }
                        }

}
}

}
void tm0_isr() interrupt 1 using 1
{
  static uchar i1,i2;
      TL0 = 0x30;             //設置定時初值  2ms
      TH0 = 0xF8;             //設置定時初值
      i1++;
  if(i1>=50)
  {
i1=0;
i2++;
if(i2>=10)
         {
         i2=0;
         time1++;
         if(time1>=60)
               {
                  time1=0;
                  time2++;
                  fen++;
   if(time2>=60)
         {
            time2=0;
               time3++;
               if(time3>=24)time3=0;
         }
                  }
                  }
  }
//dyADC();
//ad0=GetADCResult(0);
}

void tm1_isr() interrupt 3 using 1
{
TL0 = 0xB0; //設置定時初始值
TH0 = 0x3C;                //設置定時初值
//dyADC();
      if(ad0>=428)CCAP1H = CCAP1L = 142; //模塊0的捕捉/比較寄存器用來控制輸出的占?比
      if(ad0<=427&&ad0>424)CCAP1H = CCAP1L = 142;
      if(ad0<=424&&ad0>420)CCAP1H = CCAP1L = 141;
      if(ad0<=420&&ad0>416)CCAP1H = CCAP1L = 140;
      if(ad0<=416&&ad0>412)CCAP1H = CCAP1L = 139;
      if(ad0<=412&&ad0>408)CCAP1H = CCAP1L = 138;
      if(ad0<=408&&ad0>404)CCAP1H = CCAP1L = 137;
      if(ad0<=404&&ad0>400)CCAP1H = CCAP1L = 136;
      if(ad0<=400&&ad0>396)CCAP1H = CCAP1L = 135;
      if(ad0<=396&&ad0>392)CCAP1H = CCAP1L = 134;
      if(ad0<=392&&ad0>388)CCAP1H = CCAP1L = 132;//
      if(ad0<=388&&ad0>384)CCAP1H = CCAP1L = 131;
      if(ad0<=384&&ad0>380)CCAP1H = CCAP1L = 129;
      if(ad0<=380&&ad0>376)CCAP1H = CCAP1L = 128;
      if(ad0<=376&&ad0>372)CCAP1H = CCAP1L = 127;
      if(ad0<=372&&ad0>368)CCAP1H = CCAP1L = 126;//
      if(ad0<=368&&ad0>364)CCAP1H = CCAP1L = 125;
      if(ad0<=364&&ad0>360)CCAP1H = CCAP1L = 123;
      if(ad0<=360&&ad0>356)CCAP1H = CCAP1L = 122;
      if(ad0<=356&&ad0>352)CCAP1H = CCAP1L = 120;
      if(ad0<=352&&ad0>348)CCAP1H = CCAP1L = 119;
      if(ad0<=348&&ad0>344)CCAP1H = CCAP1L = 117;
      if(ad0<=344&&ad0>340)CCAP1H = CCAP1L = 116;
      if(ad0<=340&&ad0>336)CCAP1H = CCAP1L = 114;
      if(ad0<=336&&ad0>332)CCAP1H = CCAP1L = 113;
      if(ad0<=332&&ad0>328)CCAP1H = CCAP1L = 111;
      if(ad0<=328&&ad0>324)CCAP1H = CCAP1L = 109;
      if(ad0<=324&&ad0>320)CCAP1H = CCAP1L = 108;
      if(ad0<=320&&ad0>316)CCAP1H = CCAP1L = 106;
      if(ad0<=316&&ad0>312)CCAP1H = CCAP1L = 105;
      if(ad0<=312&&ad0>308)CCAP1H = CCAP1L = 103;
      if(ad0<=304&&ad0>300)CCAP1H = CCAP1L = 100;
      if(ad0<=300&&ad0>296)CCAP1H = CCAP1L = 98;
      if(ad0<=296&&ad0>292)CCAP1H = CCAP1L = 97;
      if(ad0<=292&&ad0>288)CCAP1H = CCAP1L = 94;
      if(ad0<=288&&ad0>284)CCAP1H = CCAP1L = 91;
      if(ad0<=284)CCAP1H = CCAP1L = 0xFF;

}

51hei圖片_20250127204632.jpg (45.27 KB, 下載次數: 0)

51hei圖片_20250127204656.jpg (75.54 KB, 下載次數: 0)

作者: mhb7231 時間: 2025-1-27 20:59
運行時間和檢測電壓都正常，就是PMW不正常無輸出，把ADC關掉PMW有輸出

作者: 太陽雨ZW 時間: 2025-1-28 11:09

mhb7231 發表于 2025-1-27 20:59
運行時間和檢測電壓都正常，就是PMW不正常無輸出，把ADC關掉PMW有輸出

這里的TL0,TH0改為TL1,TH1試試

2345截圖20250128105954.png (14.06 KB, 下載次數: 0)

作者: 太陽雨ZW 時間: 2025-1-28 11:27

mhb7231 發表于 2025-1-27 20:59
運行時間和檢測電壓都正常，就是PMW不正常無輸出，把ADC關掉PMW有輸出

還有這里的初始化，TL0,TH0改為TL1,TH1

2345截圖20250128112237.png (12.13 KB, 下載次數: 0)

作者: mhb7231 時間: 2025-1-30 02:35
TL0,TH0改為TL1,TH1，還是不行，

歡迎光臨 (http://www.torrancerestoration.com/bbs/)