日本最新一区二区三区免费看,男人和女人免费视频大全播放,粗壮挺进邻居人妻无码

標題: 16x64點陣顯示問題 [打印本頁]

作者: lcyzzyl 時間: 2014-11-11 14:46
標題: 16x64點陣顯示問題
近期得到一塊16x64的LED屏幕板子，板子上的集成電路有，8塊74hc595、一塊74hc245，一塊74hc123，一塊74hc367、2塊hc74138.參考網上的接口定義和驅動，能夠點亮，但出現一下問題：只送一個字的數據時，第一個字顯示正常，第二個子從第二行開始顯示，第16行在第一行顯示，第三個子從第三行顯示，第16和15行在第1和第二行顯示，第四個子從第四行顯示，第16、15和14行在第1、第2和第3行顯示，，同時送4個字的數據時，中間會有幾行不亮。試了好幾個程序都是這樣，不知問題出在程序還是板子，本人純屬愛好，望高手幫忙。

IMG_20141111_135302.jpg (1.94 MB, 下載次數: 171)

作者: xing1234 時間: 2014-11-11 16:22
板子沒什么問題，是你程序的問題，好好查一下，

作者: xing1234 時間: 2014-11-11 16:23
你一次將4個字的數據發完再鎖存就OK了

作者: lcyzzyl 時間: 2014-11-11 16:43

xing1234 發表于 2014-11-11 16:23
你一次將4個字的數據發完再鎖存就OK了

一次將4個字的數據發完,就會有幾行不亮，字顯示不全。

作者: lcyzzyl 時間: 2014-11-11 16:46
把程序附上
#include<reg52.h>

#define uchar unsigned char
#define uint unsigned int
#define hang P1 //行掃描接在P1口

sbit g1=P0^0;  //使能端OE
sbit ds=P0^1;  //紅色數據
sbit clk=P0^3;  //時鐘信號
sbit stcp=P0^2; //鎖存信號

sbit mr=P0^4;  //

uint counter;
uchar flag;
uchar code display[ ]={
/*-- 文字: 好 --*/
/*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/
0x10,0x00,0x11,0xFC,0x10,0x08,0x10,0x10,0xFC,0x20,0x24,0x20,0x24,0x20,0x27,0xFE,
0x44,0x20,0x64,0x20,0x18,0x20,0x08,0x20,0x14,0x20,0x26,0x20,0x44,0xA0,0x80,0x40,

/*-- 文字: 好 --*/
/*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/
0x10,0x00,0x11,0xFC,0x10,0x08,0x10,0x10,0xFC,0x20,0x24,0x20,0x24,0x20,0x27,0xFE,
0x44,0x20,0x64,0x20,0x18,0x20,0x08,0x20,0x14,0x20,0x26,0x20,0x44,0xA0,0x80,0x40,

/*-- 文字: 學 --*/
/*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/
0x01,0x08,0x10,0x8C,0x0C,0xC8,0x08,0x90,0x7F,0xFE,0x40,0x04,0x8F,0xE8,0x00,0x40,
0x00,0x80,0x7F,0xFE,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x02,0x80,0x01,0x00,

/*-- 文字: 習 --*/
/*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x3F,0xFC,0x00,0x04,0x08,0x04,0x04,0x04,0x03,0x04,0x01,0x14,0x00,0x64,
0x01,0x84,0x06,0x04,0x38,0x04,0x10,0x04,0x00,0x04,0x00,0x24,0x00,0x14,0x00,0x00,

/*--  文字:  天  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x3F,0xFC,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x7F,0xFE,0x00,0x80,
0x00,0x80,0x01,0x40,0x02,0x40,0x04,0x20,0x18,0x10,0x70,0x08,0x20,0x04,0x00,0x02,

/*--  文字:  天  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x3F,0xFC,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x7F,0xFE,0x00,0x80,
0x00,0x80,0x01,0x40,0x02,0x40,0x04,0x20,0x18,0x10,0x70,0x08,0x20,0x04,0x00,0x02,

/*--  文字:  向  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x40,0x00,0x20,0x3F,0xFC,0x20,0x04,0x20,0x04,0x27,0xE4,0x24,0x24,0x24,0x24,
0x24,0x24,0x24,0x24,0x27,0xE4,0x24,0x24,0x20,0x04,0x28,0x04,0x10,0x04,0x00,0x00,

/*--  文字:  上  --*/
/*--  宋體12;  此字體下對應的點陣為：寬x高=16x16 --*/
0x00,0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x1F,0x80,0x00,0x80,
0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x20,0x80,0x7F,0xFE,0x00,0x00,

};

void write_595(uchar shuju) //向595寫一個字節的數據
{
uchar i;
for(i=0;i<8;i++)
{
ds=(~shuju)&0x01;
clk=1;
clk=0;
shuju=shuju>>1;
}
}

void delay_ms(uchar x)  //x=50演延時10ms
{
uchar a,b;
for(a=x;a>0;a--)
   for(b=200;b>0;b--);
}

void main() //主函數
{


while(1)
{
uchar i,j;

for(i=100;i>0;i--)       //顯示時間

for(j=0;j<17;j++)
{



write_595(display[j*2+4*32+1]);
write_595(display[j*2+4*32]);


write_595(display[j*2+5*32+1]);
write_595(display[j*2+5*32]);




write_595(display[j*2+6*32+1]);
write_595(display[j*2+6*32]);

write_595(display[j*2+7*32+1]);
write_595(display[j*2+7*32]);

g1=0; //154使能

stcp=1;
stcp=0;

hang=j;


}

作者: lcyzzyl 時間: 2014-11-11 16:47
for(j=0;j<17;j++)應為for(j=0;j<16;j++)

作者: lcyzzyl 時間: 2014-11-11 16:48
用這個程序驅動，顯示不全

作者: lcyzzyl 時間: 2014-11-11 16:49
想弄好16x64，在弄32x64這個大板

作者: xing1234 時間: 2014-11-11 17:28
for (k=0;k<lieshu;k++) //12    lieshu
      {
         da_k=j_ram_Hang[da_H].j_ram_Lie[k] ;
         for (i=0;i<16;i++)
         {
            R1_DAT=!(da_k&0x8000);
            CK_CLK = 1;
            _nop_();
            CK_CLK = 0;
            da_k<<=1;
}
      }

作者: xing1234 時間: 2014-11-11 17:32
以前的程序，很多是對你沒用的，取了一段

作者: xing1234 時間: 2014-11-11 17:35
xdata struct j_RAM // 顯示緩存
{
U16 j_ram_Lie[PIN_ZI]; //開顯示緩沖區
}j_ram_Hang[16];

作者: xing1234 時間: 2014-11-11 17:37
要看你用的什么型號的片子，可以考慮用定時器中斷掃描

作者: xing1234 時間: 2014-11-11 17:40
先開一段RAM做顯示緩存，一行一行的掃，一行數據全部發完再鎖存，

作者: lcyzzyl 時間: 2014-11-11 20:29
這是發送四個字的顯示

IMG_20141111_165529.jpg (1.68 MB, 下載次數: 155)

作者: lcyzzyl 時間: 2014-11-11 20:30
顯示不全，就是不知道原因

作者: lcyzzyl 時間: 2014-11-11 20:49
就是不明白為什么有幾行會不亮？
用了幾個程序都是這樣

作者: lcyzzyl 時間: 2014-11-11 21:37
板子背面

IMG_20141111_165544.jpg (1.89 MB, 下載次數: 130)

作者: xing1234 時間: 2014-11-12 11:32
你第一張圖已經說是板子是好的，程序問題

作者: xing1234 時間: 2014-11-12 11:35
你這個板子是老板子了，如是你能顯示圖1的話，說明你的驅動應當是OK的，我沒細看你和程序

作者: xing1234 時間: 2014-11-12 11:43
如果需要，我?guī)啄昵坝袀€LED計算器的程序可以傳上來，你看看

作者: xing1234 時間: 2014-11-12 17:58

/*版本： 1.0    */

#include <STC12C54.H>
#include <intrins.h>
#include <absacc.h>
#include <math.h>

#define unchar unsigned char
#define unint unsigned int

/*****************關鍵值*********************/

//COM通信修改項
#define  COM_ADDRES_G 0x00       //廣播通信地址16進制
#define  com_in_data0  0xBE       // 接收開始位
#define  com_in_close  0x0D       // 接收結束位

//新舊屏修改項
//#define  EN_on             1       //掃描開    //0 新舊屏相關
//電信舊屏為0
//熊屏為1

#define  EN_off          !EN_on       //掃描       //1

//改屏字?jǐn)?shù)時修改項
#define  PIN_ZI       5       //屏總字?jǐn)?shù)       //4

#define  RAM_SHU       32*(PIN_ZI/2)       //緩沖數組大小int    //32*(PIN_ZI/2)

#define  H2_ZI       4       //第二行字中數字加入到第幾個字中間

#define  ZHI_HH       17       //數據行數    //4
#define  COM_MAX    77          //com最大接收數
#define  XIAN_id    13          //窗口號放在第幾行

/****************函數申明區************************************/
//sfr AUXR = 0x8e;
void IAP_XIE (unsigned char IAP_DATA,unsigned char ADDH,unsigned char ADDL);
unsigned char  IAP_DU (unsigned char ADDH,unsigned char ADDL);
void IAP_CACHU (unsigned char ADDH,unsigned char ADDL);

void INSZ8(void);
void com_out(void);
unsigned char hextoasc(unsigned char ascc); //輸入hex碼值,輸出 ascii碼
unsigned char ASC_TO_HEX(unsigned char ascH,unsigned char ascL); //輸出hex碼值,輸入 ascii碼

void CHU_SHI(void);

/* ISP_IAP_寄存器 */
sfr ISP_DATA  = 0xe2;
sfr ISP_ADDRH = 0xe3;
sfr ISP_ADDRL = 0xe4;
sfr ISP_CMD = 0xe5;
sfr ISP_TRIG  = 0xe6;
sfr ISP_CONTR = 0xe7;

//IO端口定義
sbit       AA = P1^0;
sbit       BB = P1^1;
sbit       CC = P1^2;
sbit       EN = P1^4; //34
sbit       DD = P1^3;
sbit       R1_DAT = P1^5;  //33
sbit       ST_RCK = P1^6;  //1.6 C5
sbit       CK_CLK = P1^7;  //1.7
sbit       LED       = P3^5;  // P3^5;

sbit       K2_A       = P3^2;
sbit       K3_B       = P3^4; //----------------------------
sbit       IN_1       = P3^7;

//sbit       RE       = P3^5;    //485發送控制
//sbit       LED       = P3^7;

//全局變量定義
unchar  da_H;                //顯示掃描行數
unsigned int xdata ZHUO_DA;
unchar  zi;                   //左移字?jǐn)?shù)累加
unsigned int xdata DAT_RAM2[RAM_SHU];  //顯示掃描緩沖區
unsigned char com_i;                //5/26
bit          com_q;

unsigned char data COM_R[COM_MAX];       //接收數據緩存 //77
bit          COM_OK;                //寫入數據完成標志位
bit          Zhi_b;                //寫入數據完成標志位

unsigned char idata H_ZHI[16];             //每行字?jǐn)?shù)
unsigned char Zhi_h,chisu;                //當前顯示字區
unsigned char YI_F;                   //移動方向選取
unsigned char idata  COM_DATA[6],COM_ADDRES;  //  4
unsigned int PAI;                   //排隊等候時間
unsigned char QIE;                   //切換時間

bit          Zhi_ZHI;                //字移完成標志位
unsigned char Z_H ; //字?jǐn)?shù)最大行數
unsigned char Z_LMAX ; // Z_LMAX=PIN_ZI*2 //掃描字?jǐn)?shù)移位確認
unsigned char SHU_1_14; //上移綬沖開始位

unsigned int    time_s;
bit          EN_on;    //  輸出EN驅動反向控制位

bit          PIN_ADD_b;    //屏地址更改標志位

bit          S1_b,S2_b,S3_b,in_b,hl_b;    //按鍵狀態標志位
unsigned char IN_HL; //輸入數據高電平/低電平有效
unsigned char IN_time;

//bit          ddd;       //叫號閃爍時間清零標志

unsigned char xdata  YI_DONG_SD[15] ; //移動速度
unsigned char xdata  YI_DONG_FX[15] ; //移動方向選取
unsigned char xdata  XIAN_SI_YS[15] ; //顯示延時
unsigned char xdata  JIAO_HAO_1[15] ; //叫號1
unsigned char xdata  JIAO_HAO_X[15] ; //叫號顯示與否標志位
unsigned char xdata  XIAN_SI_CS[15] ; //顯示次數
unsigned char xdata  TING_LUI_SJ[15] ; //停留時間
unsigned char xdata  JIAO_HAO_CS[15] ; //叫號閃動次數

//unsigned int H1_wwww ;                //第一行字中數字加入到第幾個字中間  //

unsigned char COM_EN;
//unsigned char    time_d ;
//unsigned int xdata DAT_XIAN_ID[17];  //窗口號顯示掃描緩沖區

unsigned char code Dat_pin[]=
{//橫向取模左高位,數據排列:從左到右從上到下
0x00,0x00,0x7C,0xC6,0xC6,0xCE,0xD6,0xD6,  // -0-
0xE6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x18,0x38,0x78,0x18,0x18,0x18,  // -1-
0x18,0x18,0x18,0x7E,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0x06,0x0C,0x18,0x30,  // -2-
0x60,0xC0,0xC6,0xFE,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0x06,0x06,0x3C,0x06,  // -3-
0x06,0x06,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x0C,0x1C,0x3C,0x6C,0xCC,0xFE,  // -4-
0x0C,0x0C,0x0C,0x1E,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0xC0,0xC0,0xC0,0xFC,0x0E,  // -5-
0x06,0x06,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x38,0x60,0xC0,0xC0,0xFC,0xC6,  // -6-
0xC6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0xC6,0x06,0x06,0x0C,0x18,  // -7-
0x30,0x30,0x30,0x30,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0xC6,0xC6,0x7C,0xC6,  // -8-
0xC6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0xC6,0xC6,0x7E,0x06,  // -9-
0x06,0x06,0x0C,0x78,0x00,0x00,0x00,0x00,

      0x00,0x00,0x10,0x38,0x6C,0xC6,0xC6,0xFE,  // -A-
0xC6,0xC6,0xC6,0xC6,0x00,0x00,0x00,0x00,

0x00,0x00,0xFC,0x66,0x66,0x66,0x7C,0x66,  // -B-
0x66,0x66,0x66,0xFC,0x00,0x00,0x00,0x00,

0x00,0x00,0x3C,0x66,0xC2,0xC0,0xC0,0xC0,  // -C-
0xC0,0xC2,0x66,0x3C,0x00,0x00,0x00,0x00,

0x00,0x00,0xF8,0x6C,0x66,0x66,0x66,0x66,  // -D-
0x66,0x66,0x6C,0xF8,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0x66,0x62,0x68,0x78,0x68,  // -E-
0x60,0x62,0x66,0xFE,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0x66,0x62,0x68,0x78,0x68,  // -F-
0x60,0x60,0x60,0xF0,0x00,0x00,0x00,0x00,

      0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,  // ---
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

};

/****************中斷處理程序區**************************************/
void extern0_ISR() interrupt 0 {}
void timer0_ISR () interrupt 1
{

  unchar i,j,k; //12M  1.5MS中斷一次
  unint  da_k;

TL0 = 0x78;
TH0 = 0xfa;
      TR0 = 0;
// EA  = 0;
TF0 = 0;       //time0中斷請求標志位

      if(da_H>15)
da_H=0;

      j=da_H*PIN_ZI;
for (k=0;k<PIN_ZI;k++) //12
{
         da_k=DAT_RAM2[j+k];
for (i=0;i<16;i++)
{
if(da_k&0x8000)
R1_DAT = 0;
else
R1_DAT = 1;
_nop_();
CK_CLK = 1;
_nop_();
CK_CLK = 0;
da_k<<=1;
}
}
EN =EN_off;       //0

if(da_H>7)
{
DD=1;
}
else
{
DD=0;
}
if(da_H&0x01)
AA=1;
else
AA=0;
if(da_H&0x02)
BB=1;
else
BB=0;
if(da_H&0x04)
CC=1;
else
CC=0;

ST_RCK = 1;
EN =EN_on;
ST_RCK = 0;
R1_DAT = 0;

da_H++;  //行加

TR0 = 1;
// EA  = 1;

      time_s++;

}
//通信中斷
void serial_ISR () interrupt 4
{
unsigned char    i,SBUF_lcd;
if(RI==1)
{
      SBUF_lcd = SBUF;
      if(SBUF_lcd==com_in_close)    //接收結束位
      {
         i=ASC_TO_HEX(COM_R[0],COM_R[1]);
         if((i==COM_ADDRES_G)||(i==COM_ADDRES))
         com_out();    //寫屏

         for(i=0;i<com_i;i++)
         COM_R[i]=0;
         SBUF_lcd=0;
         com_i=0;
         com_q=0;
      }
      if(com_q)
      {
         COM_R[com_i]=SBUF_lcd;
         if(com_i<COM_MAX)
         com_i++;
      }
      if(SBUF_lcd==com_in_data0)    //接收開始位
      {
         com_q=1;
         com_i=0;
      }
}
RI=0;
}
void timer2_ISR () interrupt 5{} /* not used */

unsigned char hextoasc(unsigned char ascc) //輸入hex碼值,輸出 ascii碼
{
  if(ascc>47&&ascc<58)
  return (ascc-48);
// if(ascc>64&&ascc<71)
  if(ascc>64&&ascc<92)
  return (ascc-55);
}

unsigned char ASC_TO_HEX(unsigned char ascH,unsigned char ascL) //輸出hex碼值,輸入 ascii碼
{
      unsigned char da;
      da=hextoasc(ascH);
      da<<=4;
      da|=hextoasc(ascL);
      return da;
}

void shuzhu (unchar z,unchar h)
{
   unsigned char i;
   unsigned int b;
   b=z*32;
   if(z>H_ZHI[h])
   H_ZHI[h]=z;
   h++;
   if(h>13)
   h=13;
   if(COM_EN)
   {
   for(i=0;i<32;i++)
   {
      if(b<256)
      IAP_XIE (COM_R[i],h,b) ;
      b++;
   }
   }
}

void chan_shu(unchar pp,unchar ma,unchar da)
{
   unchar i;
   if(COM_EN)
   {
   if(pp<6)
   {
      i=pp*20;
      i+=ma;
      IAP_XIE (da,0x0e,i) ;
   }
   else
   {
      pp-=6;
      i=pp*20;
      i+=ma;
      IAP_XIE (da,0x0f,i) ;
   }
   }
}
//數據接收處理
void com_out(void )
{
  unsigned char i,h,z,an,chao_zi,pp;
  unsigned int    com_k;
  unsigned char com_x;

  z=ASC_TO_HEX(COM_R[6],COM_R[7]);
  h=ASC_TO_HEX(COM_R[4],COM_R[5]);
  chao_zi=ASC_TO_HEX(COM_R[2],COM_R[3]);

  if(chao_zi==0x04||chao_zi==0x05)
  {
      com_x=ASC_TO_HEX(COM_R[com_i-2],COM_R[com_i-1]);
      com_k=0;
      for(i=0;i<com_i-2;i++)
      {
         com_k+=ASC_TO_HEX(COM_R[i],COM_R[i+1]);
         i++;
      }
      com_k%=0xff;
      if(com_x!=com_k)
      return ;
  }

  if(chao_zi==0x04)    //操作碼清EEP //操作碼1寫屏
  {
   //if(h==0)
   if(!h&&(com_i==10||com_i==12))    //=0
   {
      COM_EN=1;
      EN =EN_off;
      TR0 = 0;
      ET0=0;       //time0中斷允許控制位

      for(i=0;i<13;i++)  //5608eep為0x00--0x0F 共4K
            {
                  IAP_CACHU (i,0);       //清空EEP
                  i++;
            }
      for(i=0;i<ZHI_HH;i++)
      H_ZHI[i]=0;
   }
   else  // if(h==1) //
   if(h==1&&(com_i==8||com_i==12))
   {
      for(i=0;i<ZHI_HH;i++)
      {
         IAP_XIE (H_ZHI[i],0x0d,210+i) ;
      }
   }

}
else if(chao_zi==0x01)    //操作碼清EEP //操作碼1寫屏
{
   if(com_i<60)
   {
      for(i=8;i<72;i++)
      COM_R[i]= 0x00;
   }
   an=0 ;
   for(i=8;i<72;i++)
   {
      COM_R[an]= ASC_TO_HEX(COM_R[i],COM_R[i+1]);
      i++;
      an++;
   }
   if(h>Z_H)
   Z_H =  h ; //字?jǐn)?shù)最大行數

   shuzhu (z,h) ; //寫入數據
}
else if(chao_zi==0x05)    //操作碼清EEP //操作碼1寫屏
  {
   if(!h&&com_i==12)    //=0
   {
      EN =EN_off;
      COM_EN=1;
      TR0 = 0;
      ET0=0;       //time0中斷允許控制位

      IAP_CACHU (0x0f,0);       //清空EEP
      PIN_ADD_b=1;    //屏地址更改標志位
   }
   else    if(h==1&&com_i==12)
   {
      COM_OK=1; //寫入數據完成標志位
      COM_EN=0;
   }
}
else if(chao_zi==0x03)    //操作碼參數設置
{

//    H1_wwww=0;
      if(h==4&&PIN_ADD_b) //寫入屏地址       PIN_ADD_b=0;    //屏地址更改標志位
      {

      z=ASC_TO_HEX(COM_R[6],COM_R[7]);

      IAP_XIE (z,0x0F,250) ;
      COM_ADDRES=  IAP_DU (0x0f,250);
      PIN_ADD_b=0;    //屏地址更改標志位
      }
      else
   if(COM_EN) //寫入屏地址
   {
   if(h==0x0d) //寫入屏地址
   {
      z=ASC_TO_HEX(COM_R[6],COM_R[7]);
      IAP_XIE (z,0x0F,251) ;

   }

   else
   {
         pp=ASC_TO_HEX(COM_R[8],COM_R[9]);
         chan_shu(pp,h,z) ;
   }
   }
}
INSZ8();
}

void IAP_FUWEI (void)
{
ISP_CONTR=0x00;
ISP_CMD=0x00;
ISP_TRIG=0x00;
ISP_ADDRH=0xff;
ISP_ADDRL=0xff;

//ISP_DATA=0xff;
}

/*讀*/
unsigned char  IAP_DU (unsigned char ADDH,unsigned char ADDL)
{
ISP_ADDRH=ADDH;
ISP_ADDRL=ADDL;
ISP_CMD=0x01;
ISP_CONTR=0x84;
ISP_TRIG=0x46;
ISP_TRIG=0xB9;

  IAP_FUWEI();

return ISP_DATA;
}

/*寫*/
void IAP_XIE (unsigned char IAP_DATA,unsigned char ADDH,unsigned char ADDL)
{
ISP_ADDRH=ADDH;
ISP_ADDRL=ADDL;
ISP_DATA=IAP_DATA;
ISP_CMD=0x02;
ISP_CONTR=0x84;
ISP_TRIG=0x46;
ISP_TRIG=0xB9;

  IAP_FUWEI();
}

/*擦除*/
void IAP_CACHU (unsigned char ADDH,unsigned char ADDL)
{
ISP_ADDRH=ADDH;
ISP_ADDRL=ADDL;
ISP_CMD=0x03;
ISP_CONTR=0x84;
ISP_TRIG=0x46;
ISP_TRIG=0xB9;

IAP_FUWEI();
}

/*****************延遲DELAY******************** **/
void delay(unsigned int a)    //1-50ms /24M
{
unsigned int i;
for(;a>0;a--)
for(i=0;i<9988;i++)
      WDT_CONTR = 0x3C;       //狗;;
}
void XIE_RAM2 (unchar zhi_ju,unchar DAT_R,unchar di,bit a)
{
unsigned char  shuzhu,dat_i,i,ADDH,w;
unsigned int  k,da_k;
di=0;
if(zi>=DAT_R)
{
      Zhi_ZHI=1;
      return ;
   }
i=0;
ADDH = zhi_ju;                //取扇區地址
for(dat_i=0;dat_i<16;dat_i++)
{
      for(shuzhu=0;shuzhu<PIN_ZI;shuzhu++)    //  PIN_ZI
{

            if(a)
            {
                     if(shuzhu==di)
                     {
                              k=(COM_DATA[0]*16)+dat_i;
                              DAT_RAM2[i]=Dat_pin[k];
                              DAT_RAM2[i]<<=8;
                              k=(COM_DATA[1]*16)+dat_i;
                              DAT_RAM2[i]|=Dat_pin[k];
                              i++;
                     }
                     else if(shuzhu==di+1)
                     {
                              k=(COM_DATA[2]*16)+dat_i;
                              DAT_RAM2[i]=Dat_pin[k];
                              DAT_RAM2[i]<<=8;
                              k=(COM_DATA[3]*16)+dat_i;
                              DAT_RAM2[i]|=Dat_pin[k];
                              i++;
                     }
                     else if(shuzhu==di+2)
                     {
                              k=(COM_DATA[4]*16)+dat_i;
                              DAT_RAM2[i]=Dat_pin[k];
                              DAT_RAM2[i]<<=8;
                              k=(COM_DATA[5]*16)+dat_i;
                              DAT_RAM2[i]|=Dat_pin[k];
                              i++;
                     }
                     /*
                     else if(shuzhu==4)
                     {

                              DAT_RAM2[i]=0;

                              i++;
                     }
                     */
                     else
                     goto xei_2;
            }
            else
            {
   xei_2:
                     da_k=shuzhu*32;
                     k= dat_i+dat_i+da_k; //
                     if(k<256)
                     {
                              DAT_RAM2[i]=IAP_DU (ADDH,k);
                     }
                     else
                     {
                              w=k-256;
                              DAT_RAM2[i]=IAP_DU (ADDH+1,w);
                     }
         DAT_RAM2[i]<<=8;
                     k++;
                     if(k<256)
                     {
                              DAT_RAM2[i]|=IAP_DU (ADDH,k);
                     }
                     else
                     {
                              w=k-256;
                              DAT_RAM2[i]|=IAP_DU (ADDH+1,w);
                     }
         i++;                   //字總數0-3 總計4個字
            }
}
}
  //  zi+=4;
}

QING_RAM2()
{
unsigned char  dat_i;
for(dat_i=0;dat_i<RAM_SHU;dat_i++)
DAT_RAM2[dat_i]=0;
  //  for(dat_i=0;dat_i<16;dat_i++)
  //  DAT_XIAN_ID[dat_i]=0;
}

//開啟顯示定時掃描
void dingsi(void)
{
TMOD |= 0x01;
TH0 = 0xF8;
TL0 = 0x2f;
ET0=1;
TR0=1;
EA=1;
      PT0=1;    //優先級
}

//程序初始化
void CHU_SHI(void)
{
unsigned char i,z,an;

EN =EN_off;       //關顯示屏
dingsi();    //開啟顯示掃描定時
QING_RAM2();    //清顯示緩沖區RAM2內存
delay(10);       //開機延遲
COM_OK=0;       //寫入數據完成標志位清零
Zhi_h=0;       //當前顯示字區默認為0
Zhi_b=0;       //調用顯示標志位清零

COM_ADDRES=IAP_DU (0x0f,250);    //本機地址
z=  IAP_DU (0x0f,251);
  //  if(z)
EN_on=1;          //顯示屏亮度--1-----------------------------------------------------------
  //  else
  //  EN_on=0;
for(i=0;i<14;i++)
      {
            if(i<6)
            {
                  z=i*20;
                  an=0x0e;
            }
            else
            {
                  z=(i-6)*20;
                  an=0x0f;
            }

      }

Z_LMAX=PIN_ZI*2;
SHU_1_14=RAM_SHU-PIN_ZI;
}

void chunchu_A( sw,sb,sg,add1)
{

   IAP_CACHU (add1,0);       //清空EEP 3扇區

   IAP_XIE (sw,add1,200) ;
   IAP_XIE (sb,add1,201) ;
   IAP_XIE (sg,add1,202) ;

}

unsigned char jp(unsigned char an)
{
unsigned char i;
switch(an)
{
      case 2: //K2_A組

      WDT_CONTR = 0x3C;    //狗;;
      if(S2_b==0)       //K2_A
      {
  EXIT1 :
         if(K2_A==0)
         {
            for(i=0;i<100;i++)  ;

         if(K2_A!=0)
            goto EXIT1;
            S2_b=1;
            return 1;
         }
      }
      else
      {
         if(K2_A==1)
         {
            S2_b=0;
            return 0;
         }
      }
break;
      case 3: //K3_B組
      if(S3_b==0)
      {
  EXIT2 :
         if(K3_B==0)
         {
            for(i=0;i<100;i++)  ;
         if(K3_B!=0)
            goto EXIT2;
            S3_b=1;
            return 1;
         }
      }
      else
      {
         if(K3_B==1)
         {
            S3_b=0;
            return 0;
         }
      }
break;
}
}

unsigned char jp5S(unsigned char an)
{
unsigned char n;
unsigned int i;
switch(an)
{
      case 2: //K2_A組    按紐2清除A/B組數據

      WDT_CONTR = 0x3C;    //狗;;
      if(S2_b==0)       //K2_A       按紐2清除A/B組數據
      {
  EXIT21 :
         if(K2_A==0)
         {
            for(n=0;n<5;n++)
            {

            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
            //  WDT_CONTR = 0x3C;    //狗;;
         if(K2_A!=0)
            goto EXIT21;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K2_A!=0)
            goto EXIT21;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K2_A!=0)
            goto EXIT21;
            }
            for(i=0;i<100;i++)  ;

         if(K2_A!=0)
            goto EXIT21;
            S2_b=1;
            return 1;
         }
      }
      else
      {
         if(K2_A==1)
         {
            S2_b=0;
            return 0;
         }
      }
break;
      case 3: //K3_B組
      if(S3_b==0)
      {
  EXIT32 :
         if(K3_B==0)
         {
         for(n=0;n<5;n++)
            {

            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K3_B!=0)
            goto EXIT32;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K3_B!=0)
            goto EXIT32;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K3_B!=0)
            goto EXIT32;
            }
            S3_b=1;
            return 1;
         }
      }
      else
      {
         if(K3_B==1)
         {
            S3_b=0;
            return 0;
         }
      }
break;
}
}

void set_IN_HL(void)
{
unsigned char    i,w,bei;

w= IAP_DU (0x0A,204);
bei=w;
if(w>0)
w=1;

COM_DATA[0] =12;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值

for(i=0;i<50;i++)
{
      if(jp(3)==1)
      {
         w=!w;
      COM_DATA[0] =12;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值
}
      delay(20) ;
}
delay(200) ;
if(bei!=w)
{
      QING_RAM2();    //清顯示緩沖區RAM2內存
      delay(10) ;
      IAP_CACHU (0x0A,0);       //清空EEP 3扇區
      IAP_XIE (w,0x0A,204) ;
}
}

void set_IN_time(void)
{
unsigned char    i,w,bei;

w= IAP_DU (0x0c,204);
bei=w;
// if(w>0)
// w=1;

COM_DATA[0] =13;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值

for(i=0;i<100;i++)
{
      if(jp(3)==1)
      {
      w++;
      COM_DATA[0] =13;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值
      }
      else  if(jp(2)==1)
      {
         w--;
      COM_DATA[0] =13;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值
      }

      delay(20) ;
}
delay(200) ;

      QING_RAM2();    //清顯示緩沖區RAM2內存
      delay(10) ;
      IAP_CACHU (0x0c,0);       //清空EEP 3扇區
      IAP_XIE (w,0x0c,204) ;

}
unsigned char IN_j(void)
{
unsigned int    i;
if(in_b==0)
{
  EXIT3 :
   WDT_CONTR = 0x3C;    //狗;;
   if(IN_1==hl_b)
      {
            for(i=0;i<6000;i++)  ;
            delay(IN_time);       //延遲
         if(IN_1!=hl_b)
            goto EXIT3;
            if(IN_1==hl_b)
            for(i=0;i<6000;i++)  ;
            delay(IN_time);       //開機延遲
         if(IN_1!=hl_b)
            goto EXIT3;

            in_b=1;
            return 1;
         }
}
else
{
         if(IN_1!=hl_b)
         {
            in_b=0;
            return 0;
         }
}

}

void xianshi(unchar a0,unchar a1,unchar a2,unchar a3,unchar a4 )
{

      COM_DATA[1]=a0 ;
      COM_DATA[2]=a1 ;
      COM_DATA[3]=a2 ;
      COM_DATA[4]=a3;
      COM_DATA[5]=a4 ;
      COM_DATA[0]=16 ;
      XIE_RAM2(Zhi_h+1,H_ZHI[Zhi_h],JIAO_HAO_1[Zhi_h],JIAO_HAO_1[Zhi_h]);
// XIE_RAM2(1,16,0,1); //顯示當前A值
}

/********************8位接收設置**********************/
void INSZ8(void)
{
  SCON = 0x50;       // 晶振18.432M
  PCON |=0x80;
  TMOD |= 0X20;
  TMOD &= 0XEF;

  TH1  = 0XF6;       //9600  晶振18.432M
  TL1  = 0xf6;
  TR1=1;
  IE |= 0x90;
// RE =  0;

}
//
/*****************主程序區****************************/
void main(void)
{
unsigned char  idata i,ab_ch;
unsigned int  idata time_f;
   unsigned char idata  ucdata_B[3];
   bit    A_B,time_bit,ab_b;

      delay(1);       //開機延遲
      dingsi();    //開啟顯示掃描定時

      zi=0;
      Zhi_ZHI=0;
      time_s=0;
      da_H=0;//行掃開始值
      CHU_SHI();    //初始化

      INSZ8();       //開啟串口接收 18.432M-19200---------------

      if(jp5S(3)==1)
      set_IN_HL() ; //  輸入端高低電平有效位設置
      if(jp5S(2)==1)
      set_IN_time() ;

      time_bit=0 ;                //是否有數據需要保存標志位
      A_B=0;                   //顯示A/B組標志位
      IN_HL= IAP_DU (0x0A,204); //讀出輸入端高低電平為有效位
      IN_time= IAP_DU (0x0c,204);
      if(IN_time>200)
      {
      IN_time=5;
      IAP_CACHU (0x0c,0);       //清空EEP 3扇區
      IAP_XIE (IN_time,0x0c,204) ;

      }
      if(IN_HL>0)
      hl_b=0;
      else
      hl_b=1;

      in_b=1; //防止誤動作

      xianshi(10,11,16,16,16 ) ; //B
      delay(100) ;
      i=IAP_DU (0x04,200);
      if(i>99)
      ucdata_B[0]=0;
      else
      ucdata_B[0]= i  ;
      i=IAP_DU (0x04,201);
      if(i>99)
      ucdata_B[1]=0;
      else
      ucdata_B[1]= i ;
      i=IAP_DU (0x04,202);
      if(i>99)
      ucdata_B[2]=0;
      else
      ucdata_B[2]= i  ;

      xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
/*
      delay(200) ;

      xianshi(10,16,16,16,16 ) ; //A
      delay(200) ;
      i=IAP_DU (0x03,200);
      if(i>99)
      ucdata[0]=0;
      else
      ucdata[0]= i  ;
      i=IAP_DU (0x03,201);
      if(i>99)
      ucdata[1]=0;
      else
      ucdata[1]= i ;
      i=IAP_DU (0x03,202);
      if(i>99)
      ucdata[2]=0;
      else
      ucdata[2]= i  ;
*/
// xianshi(ucdata[2]%10,ucdata[1]/10,ucdata[1]%10,ucdata[0]/10,ucdata[0]%10 ) ; //顯示當前A值

while(1)
{
open:

      WDT_CONTR = 0x3C;       //狗;

      delay(1) ;
      i=1;
      for(i=0;i<3;i++);
      if(IN_j()==1) //有數據輸入
      {
         if(ucdata_B[0]>=99)
         {
            ucdata_B[0]=0;
            if(ucdata_B[1]>=99)
            {
                  ucdata_B[1]=0;
                  if(ucdata_B[2]>=99)
                  ucdata_B[2]=0;
                  else
                  ucdata_B[2]++;
            }
            else
            ucdata_B[1]++;
         }
         else
         ucdata_B[0]++;

            xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B

               time_f=0;
               time_s=0;
               time_bit=1;
               ab_b=0;
      }

      if(time_s>60000&&time_bit)
      {
         time_f++;
         time_s=0;
               if(time_f>5) //
               {
                     time_bit=0;
                     time_f=0;
                     chunchu_A(ucdata_B[0],ucdata_B[1],ucdata_B[2],0x04);
               }
      }
      if(jp5S(3)==1)//按紐3顯示B組數據
      {
         xianshi(11,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
         ab_b=1;
         ab_ch=0;

      }
      else
      {
         if(ab_b)
         {
               ab_ch++;
               if(ab_ch>100)
               {
               chunchu_A(ucdata_B[0],ucdata_B[1],ucdata_B[2],0x04);
               xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
               ab_b=0;
               }
         }
      }
      if(jp5S(2)==1)//按紐2清除A/B組數據
      {
            ucdata_B[0]=0;
            ucdata_B[1]=0;
            ucdata_B[2]=0;
            QING_RAM2();    //清顯示緩沖區RAM2內存
            delay(10) ;
            chunchu_A(ucdata_B[0],ucdata_B[1],ucdata_B[2],0x04);
            xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
      }
      goto open;
}
}
/*
程序完成時間：
*/

作者: xing1234 時間: 2014-11-12 18:02

/*版本： 1.0    */

#include <STC12C54.H>
#include <intrins.h>
#include <absacc.h>
#include <math.h>

#define unchar unsigned char
#define unint unsigned int

/*****************關鍵值*********************/

//COM通信修改項
#define  COM_ADDRES_G 0x00       //廣播通信地址16進制
#define  com_in_data0  0xBE       // 接收開始位
#define  com_in_close  0x0D       // 接收結束位

//新舊屏修改項
//#define  EN_on             1       //掃描開    //0 新舊屏相關
//電信舊屏為0
//熊屏為1

#define  EN_off          !EN_on       //掃描       //1

//改屏字?jǐn)?shù)時修改項
#define  PIN_ZI       5       //屏總字?jǐn)?shù)       //4

#define  RAM_SHU       32*(PIN_ZI/2)       //緩沖數組大小int    //32*(PIN_ZI/2)

#define  H2_ZI       4       //第二行字中數字加入到第幾個字中間

#define  ZHI_HH       17       //數據行數    //4
#define  COM_MAX    77          //com最大接收數
#define  XIAN_id    13          //窗口號放在第幾行

/****************函數申明區************************************/
//sfr AUXR = 0x8e;
void IAP_XIE (unsigned char IAP_DATA,unsigned char ADDH,unsigned char ADDL);
unsigned char  IAP_DU (unsigned char ADDH,unsigned char ADDL);
void IAP_CACHU (unsigned char ADDH,unsigned char ADDL);

void INSZ8(void);
void com_out(void);
unsigned char hextoasc(unsigned char ascc); //輸入hex碼值,輸出 ascii碼
unsigned char ASC_TO_HEX(unsigned char ascH,unsigned char ascL); //輸出hex碼值,輸入 ascii碼

void CHU_SHI(void);

/* ISP_IAP_寄存器 */
sfr ISP_DATA  = 0xe2;
sfr ISP_ADDRH = 0xe3;
sfr ISP_ADDRL = 0xe4;
sfr ISP_CMD = 0xe5;
sfr ISP_TRIG  = 0xe6;
sfr ISP_CONTR = 0xe7;

//IO端口定義
sbit       AA = P1^0;
sbit       BB = P1^1;
sbit       CC = P1^2;
sbit       EN = P1^4; //34
sbit       DD = P1^3;
sbit       R1_DAT = P1^5;  //33
sbit       ST_RCK = P1^6;  //1.6 C5
sbit       CK_CLK = P1^7;  //1.7
sbit       LED       = P3^5;  // P3^5;

sbit       K2_A       = P3^2;
sbit       K3_B       = P3^4; //----------------------------
sbit       IN_1       = P3^7;

//sbit       RE       = P3^5;    //485發送控制
//sbit       LED       = P3^7;

//全局變量定義
unchar  da_H;                //顯示掃描行數
unsigned int xdata ZHUO_DA;
unchar  zi;                   //左移字?jǐn)?shù)累加
unsigned int xdata DAT_RAM2[RAM_SHU];  //顯示掃描緩沖區
unsigned char com_i;                //5/26
bit          com_q;

unsigned char data COM_R[COM_MAX];       //接收數據緩存 //77
bit          COM_OK;                //寫入數據完成標志位
bit          Zhi_b;                //寫入數據完成標志位

unsigned char idata H_ZHI[16];             //每行字?jǐn)?shù)
unsigned char Zhi_h,chisu;                //當前顯示字區
unsigned char YI_F;                   //移動方向選取
unsigned char idata  COM_DATA[6],COM_ADDRES;  //  4
unsigned int PAI;                   //排隊等候時間
unsigned char QIE;                   //切換時間

bit          Zhi_ZHI;                //字移完成標志位
unsigned char Z_H ; //字?jǐn)?shù)最大行數
unsigned char Z_LMAX ; // Z_LMAX=PIN_ZI*2 //掃描字?jǐn)?shù)移位確認
unsigned char SHU_1_14; //上移綬沖開始位

unsigned int    time_s;
bit          EN_on;    //  輸出EN驅動反向控制位

bit          PIN_ADD_b;    //屏地址更改標志位

bit          S1_b,S2_b,S3_b,in_b,hl_b;    //按鍵狀態標志位
unsigned char IN_HL; //輸入數據高電平/低電平有效
unsigned char IN_time;

//bit          ddd;       //叫號閃爍時間清零標志

unsigned char xdata  YI_DONG_SD[15] ; //移動速度
unsigned char xdata  YI_DONG_FX[15] ; //移動方向選取
unsigned char xdata  XIAN_SI_YS[15] ; //顯示延時
unsigned char xdata  JIAO_HAO_1[15] ; //叫號1
unsigned char xdata  JIAO_HAO_X[15] ; //叫號顯示與否標志位
unsigned char xdata  XIAN_SI_CS[15] ; //顯示次數
unsigned char xdata  TING_LUI_SJ[15] ; //停留時間
unsigned char xdata  JIAO_HAO_CS[15] ; //叫號閃動次數

//unsigned int H1_wwww ;                //第一行字中數字加入到第幾個字中間  //

unsigned char COM_EN;
//unsigned char    time_d ;
//unsigned int xdata DAT_XIAN_ID[17];  //窗口號顯示掃描緩沖區

unsigned char code Dat_pin[]=
{//橫向取模左高位,數據排列:從左到右從上到下
0x00,0x00,0x7C,0xC6,0xC6,0xCE,0xD6,0xD6,  // -0-
0xE6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x18,0x38,0x78,0x18,0x18,0x18,  // -1-
0x18,0x18,0x18,0x7E,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0x06,0x0C,0x18,0x30,  // -2-
0x60,0xC0,0xC6,0xFE,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0x06,0x06,0x3C,0x06,  // -3-
0x06,0x06,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x0C,0x1C,0x3C,0x6C,0xCC,0xFE,  // -4-
0x0C,0x0C,0x0C,0x1E,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0xC0,0xC0,0xC0,0xFC,0x0E,  // -5-
0x06,0x06,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x38,0x60,0xC0,0xC0,0xFC,0xC6,  // -6-
0xC6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0xC6,0x06,0x06,0x0C,0x18,  // -7-
0x30,0x30,0x30,0x30,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0xC6,0xC6,0x7C,0xC6,  // -8-
0xC6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0xC6,0xC6,0x7E,0x06,  // -9-
0x06,0x06,0x0C,0x78,0x00,0x00,0x00,0x00,

      0x00,0x00,0x10,0x38,0x6C,0xC6,0xC6,0xFE,  // -A-
0xC6,0xC6,0xC6,0xC6,0x00,0x00,0x00,0x00,

0x00,0x00,0xFC,0x66,0x66,0x66,0x7C,0x66,  // -B-
0x66,0x66,0x66,0xFC,0x00,0x00,0x00,0x00,

0x00,0x00,0x3C,0x66,0xC2,0xC0,0xC0,0xC0,  // -C-
0xC0,0xC2,0x66,0x3C,0x00,0x00,0x00,0x00,

0x00,0x00,0xF8,0x6C,0x66,0x66,0x66,0x66,  // -D-
0x66,0x66,0x6C,0xF8,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0x66,0x62,0x68,0x78,0x68,  // -E-
0x60,0x62,0x66,0xFE,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0x66,0x62,0x68,0x78,0x68,  // -F-
0x60,0x60,0x60,0xF0,0x00,0x00,0x00,0x00,

      0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,  // ---
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

};

/****************中斷處理程序區**************************************/
void extern0_ISR() interrupt 0 {}
void timer0_ISR () interrupt 1
{

  unchar i,j,k; //12M  1.5MS中斷一次
  unint  da_k;

TL0 = 0x78;
TH0 = 0xfa;
      TR0 = 0;
// EA  = 0;
TF0 = 0;       //time0中斷請求標志位

      if(da_H>15)
da_H=0;

      j=da_H*PIN_ZI;
for (k=0;k<PIN_ZI;k++) //12
{
         da_k=DAT_RAM2[j+k];
for (i=0;i<16;i++)
{
if(da_k&0x8000)
R1_DAT = 0;
else
R1_DAT = 1;
_nop_();
CK_CLK = 1;
_nop_();
CK_CLK = 0;
da_k<<=1;
}
}
EN =EN_off;       //0

if(da_H>7)
{
DD=1;
}
else
{
DD=0;
}
if(da_H&0x01)
AA=1;
else
AA=0;
if(da_H&0x02)
BB=1;
else
BB=0;
if(da_H&0x04)
CC=1;
else
CC=0;

ST_RCK = 1;
EN =EN_on;
ST_RCK = 0;
R1_DAT = 0;

da_H++;  //行加

TR0 = 1;
// EA  = 1;

      time_s++;

}
//通信中斷
void serial_ISR () interrupt 4
{
unsigned char    i,SBUF_lcd;
if(RI==1)
{
      SBUF_lcd = SBUF;
      if(SBUF_lcd==com_in_close)    //接收結束位
      {
         i=ASC_TO_HEX(COM_R[0],COM_R[1]);
         if((i==COM_ADDRES_G)||(i==COM_ADDRES))
         com_out();    //寫屏

         for(i=0;i<com_i;i++)
         COM_R[i]=0;
         SBUF_lcd=0;
         com_i=0;
         com_q=0;
      }
      if(com_q)
      {
         COM_R[com_i]=SBUF_lcd;
         if(com_i<COM_MAX)
         com_i++;
      }
      if(SBUF_lcd==com_in_data0)    //接收開始位
      {
         com_q=1;
         com_i=0;
      }
}
RI=0;
}
void timer2_ISR () interrupt 5{} /* not used */

unsigned char hextoasc(unsigned char ascc) //輸入hex碼值,輸出 ascii碼
{
  if(ascc>47&&ascc<58)
  return (ascc-48);
// if(ascc>64&&ascc<71)
  if(ascc>64&&ascc<92)
  return (ascc-55);
}

unsigned char ASC_TO_HEX(unsigned char ascH,unsigned char ascL) //輸出hex碼值,輸入 ascii碼
{
      unsigned char da;
      da=hextoasc(ascH);
      da<<=4;
      da|=hextoasc(ascL);
      return da;
}

void shuzhu (unchar z,unchar h)
{
   unsigned char i;
   unsigned int b;
   b=z*32;
   if(z>H_ZHI[h])
   H_ZHI[h]=z;
   h++;
   if(h>13)
   h=13;
   if(COM_EN)
   {
   for(i=0;i<32;i++)
   {
      if(b<256)
      IAP_XIE (COM_R[i],h,b) ;
      b++;
   }
   }
}

void chan_shu(unchar pp,unchar ma,unchar da)
{
   unchar i;
   if(COM_EN)
   {
   if(pp<6)
   {
      i=pp*20;
      i+=ma;
      IAP_XIE (da,0x0e,i) ;
   }
   else
   {
      pp-=6;
      i=pp*20;
      i+=ma;
      IAP_XIE (da,0x0f,i) ;
   }
   }
}
//數據接收處理
void com_out(void )
{
  unsigned char i,h,z,an,chao_zi,pp;
  unsigned int    com_k;
  unsigned char com_x;

  z=ASC_TO_HEX(COM_R[6],COM_R[7]);
  h=ASC_TO_HEX(COM_R[4],COM_R[5]);
  chao_zi=ASC_TO_HEX(COM_R[2],COM_R[3]);

  if(chao_zi==0x04||chao_zi==0x05)
  {
      com_x=ASC_TO_HEX(COM_R[com_i-2],COM_R[com_i-1]);
      com_k=0;
      for(i=0;i<com_i-2;i++)
      {
         com_k+=ASC_TO_HEX(COM_R[i],COM_R[i+1]);
         i++;
      }
      com_k%=0xff;
      if(com_x!=com_k)
      return ;
  }

  if(chao_zi==0x04)    //操作碼清EEP //操作碼1寫屏
  {
   //if(h==0)
   if(!h&&(com_i==10||com_i==12))    //=0
   {
      COM_EN=1;
      EN =EN_off;
      TR0 = 0;
      ET0=0;       //time0中斷允許控制位

      for(i=0;i<13;i++)  //5608eep為0x00--0x0F 共4K
            {
                  IAP_CACHU (i,0);       //清空EEP
                  i++;
            }
      for(i=0;i<ZHI_HH;i++)
      H_ZHI[i]=0;
   }
   else  // if(h==1) //
   if(h==1&&(com_i==8||com_i==12))
   {
      for(i=0;i<ZHI_HH;i++)
      {
         IAP_XIE (H_ZHI[i],0x0d,210+i) ;
      }
   }

}
else if(chao_zi==0x01)    //操作碼清EEP //操作碼1寫屏
{
   if(com_i<60)
   {
      for(i=8;i<72;i++)
      COM_R[i]= 0x00;
   }
   an=0 ;
   for(i=8;i<72;i++)
   {
      COM_R[an]= ASC_TO_HEX(COM_R[i],COM_R[i+1]);
      i++;
      an++;
   }
   if(h>Z_H)
   Z_H =  h ; //字?jǐn)?shù)最大行數

   shuzhu (z,h) ; //寫入數據
}
else if(chao_zi==0x05)    //操作碼清EEP //操作碼1寫屏
  {
   if(!h&&com_i==12)    //=0
   {
      EN =EN_off;
      COM_EN=1;
      TR0 = 0;
      ET0=0;       //time0中斷允許控制位

      IAP_CACHU (0x0f,0);       //清空EEP
      PIN_ADD_b=1;    //屏地址更改標志位
   }
   else    if(h==1&&com_i==12)
   {
      COM_OK=1; //寫入數據完成標志位
      COM_EN=0;
   }
}
else if(chao_zi==0x03)    //操作碼參數設置
{

//    H1_wwww=0;
      if(h==4&&PIN_ADD_b) //寫入屏地址       PIN_ADD_b=0;    //屏地址更改標志位
      {

      z=ASC_TO_HEX(COM_R[6],COM_R[7]);

      IAP_XIE (z,0x0F,250) ;
      COM_ADDRES=  IAP_DU (0x0f,250);
      PIN_ADD_b=0;    //屏地址更改標志位
      }
      else
   if(COM_EN) //寫入屏地址
   {
   if(h==0x0d) //寫入屏地址
   {
      z=ASC_TO_HEX(COM_R[6],COM_R[7]);
      IAP_XIE (z,0x0F,251) ;

   }

   else
   {
         pp=ASC_TO_HEX(COM_R[8],COM_R[9]);
         chan_shu(pp,h,z) ;
   }
   }
}
INSZ8();
}

void IAP_FUWEI (void)
{
ISP_CONTR=0x00;
ISP_CMD=0x00;
ISP_TRIG=0x00;
ISP_ADDRH=0xff;
ISP_ADDRL=0xff;

//ISP_DATA=0xff;
}

/*讀*/
unsigned char  IAP_DU (unsigned char ADDH,unsigned char ADDL)
{
ISP_ADDRH=ADDH;
ISP_ADDRL=ADDL;
ISP_CMD=0x01;
ISP_CONTR=0x84;
ISP_TRIG=0x46;
ISP_TRIG=0xB9;

  IAP_FUWEI();

return ISP_DATA;
}

/*寫*/
void IAP_XIE (unsigned char IAP_DATA,unsigned char ADDH,unsigned char ADDL)
{
ISP_ADDRH=ADDH;
ISP_ADDRL=ADDL;
ISP_DATA=IAP_DATA;
ISP_CMD=0x02;
ISP_CONTR=0x84;
ISP_TRIG=0x46;
ISP_TRIG=0xB9;

  IAP_FUWEI();
}

/*擦除*/
void IAP_CACHU (unsigned char ADDH,unsigned char ADDL)
{
ISP_ADDRH=ADDH;
ISP_ADDRL=ADDL;
ISP_CMD=0x03;
ISP_CONTR=0x84;
ISP_TRIG=0x46;
ISP_TRIG=0xB9;

IAP_FUWEI();
}

/*****************延遲DELAY******************** **/
void delay(unsigned int a)    //1-50ms /24M
{
unsigned int i;
for(;a>0;a--)
for(i=0;i<9988;i++)
      WDT_CONTR = 0x3C;       //狗;;
}
void XIE_RAM2 (unchar zhi_ju,unchar DAT_R,unchar di,bit a)
{
unsigned char  shuzhu,dat_i,i,ADDH,w;
unsigned int  k,da_k;
di=0;
if(zi>=DAT_R)
{
      Zhi_ZHI=1;
      return ;
   }
i=0;
ADDH = zhi_ju;                //取扇區地址
for(dat_i=0;dat_i<16;dat_i++)
{
      for(shuzhu=0;shuzhu<PIN_ZI;shuzhu++)    //  PIN_ZI
{

            if(a)
            {
                     if(shuzhu==di)
                     {
                              k=(COM_DATA[0]*16)+dat_i;
                              DAT_RAM2[i]=Dat_pin[k];
                              DAT_RAM2[i]<<=8;
                              k=(COM_DATA[1]*16)+dat_i;
                              DAT_RAM2[i]|=Dat_pin[k];
                              i++;
                     }
                     else if(shuzhu==di+1)
                     {
                              k=(COM_DATA[2]*16)+dat_i;
                              DAT_RAM2[i]=Dat_pin[k];
                              DAT_RAM2[i]<<=8;
                              k=(COM_DATA[3]*16)+dat_i;
                              DAT_RAM2[i]|=Dat_pin[k];
                              i++;
                     }
                     else if(shuzhu==di+2)
                     {
                              k=(COM_DATA[4]*16)+dat_i;
                              DAT_RAM2[i]=Dat_pin[k];
                              DAT_RAM2[i]<<=8;
                              k=(COM_DATA[5]*16)+dat_i;
                              DAT_RAM2[i]|=Dat_pin[k];
                              i++;
                     }
                     /*
                     else if(shuzhu==4)
                     {

                              DAT_RAM2[i]=0;

                              i++;
                     }
                     */
                     else
                     goto xei_2;
            }
            else
            {
   xei_2:
                     da_k=shuzhu*32;
                     k= dat_i+dat_i+da_k; //
                     if(k<256)
                     {
                              DAT_RAM2[i]=IAP_DU (ADDH,k);
                     }
                     else
                     {
                              w=k-256;
                              DAT_RAM2[i]=IAP_DU (ADDH+1,w);
                     }
         DAT_RAM2[i]<<=8;
                     k++;
                     if(k<256)
                     {
                              DAT_RAM2[i]|=IAP_DU (ADDH,k);
                     }
                     else
                     {
                              w=k-256;
                              DAT_RAM2[i]|=IAP_DU (ADDH+1,w);
                     }
         i++;                   //字總數0-3 總計4個字
            }
}
}
  //  zi+=4;
}

QING_RAM2()
{
unsigned char  dat_i;
for(dat_i=0;dat_i<RAM_SHU;dat_i++)
DAT_RAM2[dat_i]=0;
  //  for(dat_i=0;dat_i<16;dat_i++)
  //  DAT_XIAN_ID[dat_i]=0;
}

//開啟顯示定時掃描
void dingsi(void)
{
TMOD |= 0x01;
TH0 = 0xF8;
TL0 = 0x2f;
ET0=1;
TR0=1;
EA=1;
      PT0=1;    //優先級
}

//程序初始化
void CHU_SHI(void)
{
unsigned char i,z,an;

EN =EN_off;       //關顯示屏
dingsi();    //開啟顯示掃描定時
QING_RAM2();    //清顯示緩沖區RAM2內存
delay(10);       //開機延遲
COM_OK=0;       //寫入數據完成標志位清零
Zhi_h=0;       //當前顯示字區默認為0
Zhi_b=0;       //調用顯示標志位清零

COM_ADDRES=IAP_DU (0x0f,250);    //本機地址
z=  IAP_DU (0x0f,251);
  //  if(z)
EN_on=1;          //顯示屏亮度--1-----------------------------------------------------------
  //  else
  //  EN_on=0;
for(i=0;i<14;i++)
      {
            if(i<6)
            {
                  z=i*20;
                  an=0x0e;
            }
            else
            {
                  z=(i-6)*20;
                  an=0x0f;
            }

      }

Z_LMAX=PIN_ZI*2;
SHU_1_14=RAM_SHU-PIN_ZI;
}

void chunchu_A( sw,sb,sg,add1)
{

   IAP_CACHU (add1,0);       //清空EEP 3扇區

   IAP_XIE (sw,add1,200) ;
   IAP_XIE (sb,add1,201) ;
   IAP_XIE (sg,add1,202) ;

}

unsigned char jp(unsigned char an)
{
unsigned char i;
switch(an)
{
      case 2: //K2_A組

      WDT_CONTR = 0x3C;    //狗;;
      if(S2_b==0)       //K2_A
      {
  EXIT1 :
         if(K2_A==0)
         {
            for(i=0;i<100;i++)  ;

         if(K2_A!=0)
            goto EXIT1;
            S2_b=1;
            return 1;
         }
      }
      else
      {
         if(K2_A==1)
         {
            S2_b=0;
            return 0;
         }
      }
break;
      case 3: //K3_B組
      if(S3_b==0)
      {
  EXIT2 :
         if(K3_B==0)
         {
            for(i=0;i<100;i++)  ;
         if(K3_B!=0)
            goto EXIT2;
            S3_b=1;
            return 1;
         }
      }
      else
      {
         if(K3_B==1)
         {
            S3_b=0;
            return 0;
         }
      }
break;
}
}

unsigned char jp5S(unsigned char an)
{
unsigned char n;
unsigned int i;
switch(an)
{
      case 2: //K2_A組    按紐2清除A/B組數據

      WDT_CONTR = 0x3C;    //狗;;
      if(S2_b==0)       //K2_A       按紐2清除A/B組數據
      {
  EXIT21 :
         if(K2_A==0)
         {
            for(n=0;n<5;n++)
            {

            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
            //  WDT_CONTR = 0x3C;    //狗;;
         if(K2_A!=0)
            goto EXIT21;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K2_A!=0)
            goto EXIT21;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K2_A!=0)
            goto EXIT21;
            }
            for(i=0;i<100;i++)  ;

         if(K2_A!=0)
            goto EXIT21;
            S2_b=1;
            return 1;
         }
      }
      else
      {
         if(K2_A==1)
         {
            S2_b=0;
            return 0;
         }
      }
break;
      case 3: //K3_B組
      if(S3_b==0)
      {
  EXIT32 :
         if(K3_B==0)
         {
         for(n=0;n<5;n++)
            {

            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K3_B!=0)
            goto EXIT32;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K3_B!=0)
            goto EXIT32;
            for(i=0;i<6000;i++)  ;
            delay(36);       //延遲
         if(K3_B!=0)
            goto EXIT32;
            }
            S3_b=1;
            return 1;
         }
      }
      else
      {
         if(K3_B==1)
         {
            S3_b=0;
            return 0;
         }
      }
break;
}
}

void set_IN_HL(void)
{
unsigned char    i,w,bei;

w= IAP_DU (0x0A,204);
bei=w;
if(w>0)
w=1;

COM_DATA[0] =12;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值

for(i=0;i<50;i++)
{
      if(jp(3)==1)
      {
         w=!w;
      COM_DATA[0] =12;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值
}
      delay(20) ;
}
delay(200) ;
if(bei!=w)
{
      QING_RAM2();    //清顯示緩沖區RAM2內存
      delay(10) ;
      IAP_CACHU (0x0A,0);       //清空EEP 3扇區
      IAP_XIE (w,0x0A,204) ;
}
}

void set_IN_time(void)
{
unsigned char    i,w,bei;

w= IAP_DU (0x0c,204);
bei=w;
// if(w>0)
// w=1;

COM_DATA[0] =13;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值

for(i=0;i<100;i++)
{
      if(jp(3)==1)
      {
      w++;
      COM_DATA[0] =13;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值
      }
      else  if(jp(2)==1)
      {
         w--;
      COM_DATA[0] =13;
COM_DATA[1] =0;
COM_DATA[2] =0;
COM_DATA[3] =0;
COM_DATA[5] =0;
COM_DATA[4] =w; //最后一位
XIE_RAM2(1,16,0,1); //顯示當前A值
      }

      delay(20) ;
}
delay(200) ;

      QING_RAM2();    //清顯示緩沖區RAM2內存
      delay(10) ;
      IAP_CACHU (0x0c,0);       //清空EEP 3扇區
      IAP_XIE (w,0x0c,204) ;

}
unsigned char IN_j(void)
{
unsigned int    i;
if(in_b==0)
{
  EXIT3 :
   WDT_CONTR = 0x3C;    //狗;;
   if(IN_1==hl_b)
      {
            for(i=0;i<6000;i++)  ;
            delay(IN_time);       //延遲
         if(IN_1!=hl_b)
            goto EXIT3;
            if(IN_1==hl_b)
            for(i=0;i<6000;i++)  ;
            delay(IN_time);       //開機延遲
         if(IN_1!=hl_b)
            goto EXIT3;

            in_b=1;
            return 1;
         }
}
else
{
         if(IN_1!=hl_b)
         {
            in_b=0;
            return 0;
         }
}

}

void xianshi(unchar a0,unchar a1,unchar a2,unchar a3,unchar a4 )
{

      COM_DATA[1]=a0 ;
      COM_DATA[2]=a1 ;
      COM_DATA[3]=a2 ;
      COM_DATA[4]=a3;
      COM_DATA[5]=a4 ;
      COM_DATA[0]=16 ;
      XIE_RAM2(Zhi_h+1,H_ZHI[Zhi_h],JIAO_HAO_1[Zhi_h],JIAO_HAO_1[Zhi_h]);
// XIE_RAM2(1,16,0,1); //顯示當前A值
}

/********************8位接收設置**********************/
void INSZ8(void)
{
  SCON = 0x50;       // 晶振18.432M
  PCON |=0x80;
  TMOD |= 0X20;
  TMOD &= 0XEF;

  TH1  = 0XF6;       //9600  晶振18.432M
  TL1  = 0xf6;
  TR1=1;
  IE |= 0x90;
// RE =  0;

}
//
/*****************主程序區****************************/
void main(void)
{
unsigned char  idata i,ab_ch;
unsigned int  idata time_f;
   unsigned char idata  ucdata_B[3];
   bit    A_B,time_bit,ab_b;

      delay(1);       //開機延遲
      dingsi();    //開啟顯示掃描定時

      zi=0;
      Zhi_ZHI=0;
      time_s=0;
      da_H=0;//行掃開始值
      CHU_SHI();    //初始化

      INSZ8();       //開啟串口接收 18.432M-19200---------------

      if(jp5S(3)==1)
      set_IN_HL() ; //  輸入端高低電平有效位設置
      if(jp5S(2)==1)
      set_IN_time() ;

      time_bit=0 ;                //是否有數據需要保存標志位
      A_B=0;                   //顯示A/B組標志位
      IN_HL= IAP_DU (0x0A,204); //讀出輸入端高低電平為有效位
      IN_time= IAP_DU (0x0c,204);
      if(IN_time>200)
      {
      IN_time=5;
      IAP_CACHU (0x0c,0);       //清空EEP 3扇區
      IAP_XIE (IN_time,0x0c,204) ;

      }
      if(IN_HL>0)
      hl_b=0;
      else
      hl_b=1;

      in_b=1; //防止誤動作

      xianshi(10,11,16,16,16 ) ; //B
      delay(100) ;
      i=IAP_DU (0x04,200);
      if(i>99)
      ucdata_B[0]=0;
      else
      ucdata_B[0]= i  ;
      i=IAP_DU (0x04,201);
      if(i>99)
      ucdata_B[1]=0;
      else
      ucdata_B[1]= i ;
      i=IAP_DU (0x04,202);
      if(i>99)
      ucdata_B[2]=0;
      else
      ucdata_B[2]= i  ;

      xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
/*
      delay(200) ;

      xianshi(10,16,16,16,16 ) ; //A
      delay(200) ;
      i=IAP_DU (0x03,200);
      if(i>99)
      ucdata[0]=0;
      else
      ucdata[0]= i  ;
      i=IAP_DU (0x03,201);
      if(i>99)
      ucdata[1]=0;
      else
      ucdata[1]= i ;
      i=IAP_DU (0x03,202);
      if(i>99)
      ucdata[2]=0;
      else
      ucdata[2]= i  ;
*/
// xianshi(ucdata[2]%10,ucdata[1]/10,ucdata[1]%10,ucdata[0]/10,ucdata[0]%10 ) ; //顯示當前A值

while(1)
{
open:

      WDT_CONTR = 0x3C;       //狗;

      delay(1) ;
      i=1;
      for(i=0;i<3;i++);
      if(IN_j()==1) //有數據輸入
      {
         if(ucdata_B[0]>=99)
         {
            ucdata_B[0]=0;
            if(ucdata_B[1]>=99)
            {
                  ucdata_B[1]=0;
                  if(ucdata_B[2]>=99)
                  ucdata_B[2]=0;
                  else
                  ucdata_B[2]++;
            }
            else
            ucdata_B[1]++;
         }
         else
         ucdata_B[0]++;

            xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B

               time_f=0;
               time_s=0;
               time_bit=1;
               ab_b=0;
      }

      if(time_s>60000&&time_bit)
      {
         time_f++;
         time_s=0;
               if(time_f>5) //
               {
                     time_bit=0;
                     time_f=0;
                     chunchu_A(ucdata_B[0],ucdata_B[1],ucdata_B[2],0x04);
               }
      }
      if(jp5S(3)==1)//按紐3顯示B組數據
      {
         xianshi(11,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
         ab_b=1;
         ab_ch=0;

      }
      else
      {
         if(ab_b)
         {
               ab_ch++;
               if(ab_ch>100)
               {
               chunchu_A(ucdata_B[0],ucdata_B[1],ucdata_B[2],0x04);
               xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
               ab_b=0;
               }
         }
      }
      if(jp5S(2)==1)//按紐2清除A/B組數據
      {
            ucdata_B[0]=0;
            ucdata_B[1]=0;
            ucdata_B[2]=0;
            QING_RAM2();    //清顯示緩沖區RAM2內存
            delay(10) ;
            chunchu_A(ucdata_B[0],ucdata_B[1],ucdata_B[2],0x04);
            xianshi(ucdata_B[2]%10,ucdata_B[1]/10,ucdata_B[1]%10,ucdata_B[0]/10,ucdata_B[0]%10 ) ; ////顯示當前值B
      }
      goto open;
}
}
/*
程序完成時間：
*/

作者: xing1234 時間: 2014-11-12 18:04
一次發不了太多

作者: xing1234 時間: 2014-11-12 18:05
#include <STC12C54.H>
#include <intrins.h>
#include <absacc.h>
#include <math.h>

#define unchar unsigned char
#define unint unsigned int

/*****************關鍵值*********************/

//COM通信修改項
#define  COM_ADDRES_G 0x00       //廣播通信地址16進制
#define  com_in_data0  0xBE       // 接收開始位
#define  com_in_close  0x0D       // 接收結束位

//新舊屏修改項
//#define  EN_on             1       //掃描開    //0 新舊屏相關
//電信舊屏為0
//熊屏為1

#define  EN_off          !EN_on       //掃描       //1

//改屏字?jǐn)?shù)時修改項
#define  PIN_ZI       5       //屏總字?jǐn)?shù)       //4

#define  RAM_SHU       32*(PIN_ZI/2)       //緩沖數組大小int    //32*(PIN_ZI/2)

#define  H2_ZI       4       //第二行字中數字加入到第幾個字中間

#define  ZHI_HH       17       //數據行數    //4
#define  COM_MAX    77          //com最大接收數
#define  XIAN_id    13          //窗口號放在第幾行

/****************函數申明區************************************/
//sfr AUXR = 0x8e;
void IAP_XIE (unsigned char IAP_DATA,unsigned char ADDH,unsigned char ADDL);
unsigned char  IAP_DU (unsigned char ADDH,unsigned char ADDL);
void IAP_CACHU (unsigned char ADDH,unsigned char ADDL);

void INSZ8(void);
void com_out(void);
unsigned char hextoasc(unsigned char ascc); //輸入hex碼值,輸出 ascii碼
unsigned char ASC_TO_HEX(unsigned char ascH,unsigned char ascL); //輸出hex碼值,輸入 ascii碼

void CHU_SHI(void);

/* ISP_IAP_寄存器 */
sfr ISP_DATA  = 0xe2;
sfr ISP_ADDRH = 0xe3;
sfr ISP_ADDRL = 0xe4;
sfr ISP_CMD = 0xe5;
sfr ISP_TRIG  = 0xe6;
sfr ISP_CONTR = 0xe7;

//IO端口定義
sbit       AA = P1^0;
sbit       BB = P1^1;
sbit       CC = P1^2;
sbit       EN = P1^4; //34
sbit       DD = P1^3;
sbit       R1_DAT = P1^5;  //33
sbit       ST_RCK = P1^6;  //1.6 C5
sbit       CK_CLK = P1^7;  //1.7
sbit       LED       = P3^5;  // P3^5;

sbit       K2_A       = P3^2;
sbit       K3_B       = P3^4; //----------------------------
sbit       IN_1       = P3^7;

//sbit       RE       = P3^5;    //485發送控制
//sbit       LED       = P3^7;

//全局變量定義
unchar  da_H;                //顯示掃描行數
unsigned int xdata ZHUO_DA;
unchar  zi;                   //左移字?jǐn)?shù)累加
unsigned int xdata DAT_RAM2[RAM_SHU];  //顯示掃描緩沖區
unsigned char com_i;                //5/26
bit          com_q;

unsigned char data COM_R[COM_MAX];       //接收數據緩存 //77
bit          COM_OK;                //寫入數據完成標志位
bit          Zhi_b;                //寫入數據完成標志位

unsigned char idata H_ZHI[16];             //每行字?jǐn)?shù)
unsigned char Zhi_h,chisu;                //當前顯示字區
unsigned char YI_F;                   //移動方向選取
unsigned char idata  COM_DATA[6],COM_ADDRES;  //  4
unsigned int PAI;                   //排隊等候時間
unsigned char QIE;                   //切換時間

bit          Zhi_ZHI;                //字移完成標志位
unsigned char Z_H ; //字?jǐn)?shù)最大行數
unsigned char Z_LMAX ; // Z_LMAX=PIN_ZI*2 //掃描字?jǐn)?shù)移位確認
unsigned char SHU_1_14; //上移綬沖開始位

unsigned int    time_s;
bit          EN_on;    //  輸出EN驅動反向控制位

bit          PIN_ADD_b;    //屏地址更改標志位

bit          S1_b,S2_b,S3_b,in_b,hl_b;    //按鍵狀態標志位
unsigned char IN_HL; //輸入數據高電平/低電平有效
unsigned char IN_time;

//bit          ddd;       //叫號閃爍時間清零標志

unsigned char xdata  YI_DONG_SD[15] ; //移動速度
unsigned char xdata  YI_DONG_FX[15] ; //移動方向選取
unsigned char xdata  XIAN_SI_YS[15] ; //顯示延時
unsigned char xdata  JIAO_HAO_1[15] ; //叫號1
unsigned char xdata  JIAO_HAO_X[15] ; //叫號顯示與否標志位
unsigned char xdata  XIAN_SI_CS[15] ; //顯示次數
unsigned char xdata  TING_LUI_SJ[15] ; //停留時間
unsigned char xdata  JIAO_HAO_CS[15] ; //叫號閃動次數

//unsigned int H1_wwww ;                //第一行字中數字加入到第幾個字中間  //

unsigned char COM_EN;
//unsigned char    time_d ;
//unsigned int xdata DAT_XIAN_ID[17];  //窗口號顯示掃描緩沖區

unsigned char code Dat_pin[]=
{//橫向取模左高位,數據排列:從左到右從上到下
0x00,0x00,0x7C,0xC6,0xC6,0xCE,0xD6,0xD6,  // -0-
0xE6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x18,0x38,0x78,0x18,0x18,0x18,  // -1-
0x18,0x18,0x18,0x7E,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0x06,0x0C,0x18,0x30,  // -2-
0x60,0xC0,0xC6,0xFE,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0x06,0x06,0x3C,0x06,  // -3-
0x06,0x06,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x0C,0x1C,0x3C,0x6C,0xCC,0xFE,  // -4-
0x0C,0x0C,0x0C,0x1E,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0xC0,0xC0,0xC0,0xFC,0x0E,  // -5-
0x06,0x06,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x38,0x60,0xC0,0xC0,0xFC,0xC6,  // -6-
0xC6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0xC6,0x06,0x06,0x0C,0x18,  // -7-
0x30,0x30,0x30,0x30,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0xC6,0xC6,0x7C,0xC6,  // -8-
0xC6,0xC6,0xC6,0x7C,0x00,0x00,0x00,0x00,

0x00,0x00,0x7C,0xC6,0xC6,0xC6,0x7E,0x06,  // -9-
0x06,0x06,0x0C,0x78,0x00,0x00,0x00,0x00,

      0x00,0x00,0x10,0x38,0x6C,0xC6,0xC6,0xFE,  // -A-
0xC6,0xC6,0xC6,0xC6,0x00,0x00,0x00,0x00,

0x00,0x00,0xFC,0x66,0x66,0x66,0x7C,0x66,  // -B-
0x66,0x66,0x66,0xFC,0x00,0x00,0x00,0x00,

0x00,0x00,0x3C,0x66,0xC2,0xC0,0xC0,0xC0,  // -C-
0xC0,0xC2,0x66,0x3C,0x00,0x00,0x00,0x00,

0x00,0x00,0xF8,0x6C,0x66,0x66,0x66,0x66,  // -D-
0x66,0x66,0x6C,0xF8,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0x66,0x62,0x68,0x78,0x68,  // -E-
0x60,0x62,0x66,0xFE,0x00,0x00,0x00,0x00,

0x00,0x00,0xFE,0x66,0x62,0x68,0x78,0x68,  // -F-
0x60,0x60,0x60,0xF0,0x00,0x00,0x00,0x00,

      0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,  // ---
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

};

作者: xing1234 時間: 2014-11-13 08:23
需要審核所，我以為沒發得起，反復發了幾次，
這程序是以前的，很多對你沒什么用，比如EEP串口通信等，當時編得不是很好，你取你需要的部分就成

作者: xing1234 時間: 2014-11-13 08:24
ICi是STC5608，晶振18。432

作者: lcyzzyl 時間: 2014-11-14 11:02

xing1234 發表于 2014-11-13 08:24
ICi是STC5608，晶振18。432

非常感謝你，經過實驗，原來是板子上的74hc123工作不正常引起的，可能是我的程序達不到原來板子的刷新頻率，導致74hc123工作不正�！，F(xiàn)在把板子上的74hc123去掉，把一塊138的6腳接vcc，另一塊138的4腳接地，讓138正常工作，顯示就正常了。

作者: hf51hei 時間: 2017-12-12 10:41
樓主的思路好啊。通過調整，把板子搞好了，值得借鑒。向樓主學習。

作者: hf51hei 時間: 2017-12-12 10:43

xing1234 發表于 2014-11-12 18:02
/*版本： 1.0 */

#include

厲害啊，欣賞欣賞。謝謝

歡迎光臨 (http://www.torrancerestoration.com/bbs/)