標題: stm32定時一秒LED亮程序 [打印本頁]
作者: geige    時間: 2015-7-26 02:17
標題: stm32定時一秒LED亮程序
//定時一秒LED亮
#include "stm32f10x.h"

unsigned intTimingDelay;

void Delay(unsigned intx)
{

TimingDelay=x;
while(TimingDelay--);
}

voidTIM3_IRQHandler(void)
{
if(TIM_GetITStatus(TIM2,TIM_IT_Update) !=RESET)//檢查中斷溢出標志位
{
TIM_ClearITPendingBit(TIM2,TIM_IT_Update);//清中斷溢出標志位
GPIO_SetBits(GPIOC,GPIO_Pin_7);
}

}


int main(void)
{
SystemInit();
  
//配置IO口
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC | RCC_APB2Periph_GPIOD| RCC_APB2Periph_GPIOE,ENABLE);//IO口使能設置
  GPIO_InitTypeDefGPIO_InitStructure;   //定義結構體
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;   
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_Init(GPIOC,&GPIO_InitStructure);
  
//設置定時器2
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);//打開TIM2外設時鐘
TIM_TimeBaseStructure.TIM_Period = 10000;//1s
TIM_TimeBaseStructure.TIM_Prescaler = 7199;//7200分頻
TIM_TimeBaseStructure.TIM_ClockDivision = 0;//設置時鐘分割
TIM_TimeBaseStructure.TIM_CounterMode =TIM_CounterMode_Up;//設置計數方式為向上計數
TIM_TimeBaseInit(TIM2,&TIM_TimeBaseStructure);//初始化定時器2
TIM_ITConfig(TIM2,TIM_IT_Update,ENABLE);//打開定時器2中斷
TIM_Cmd(TIM2,ENABLE);//使能定時器
  
  
//使能TIM2中斷
  NVIC_InitTypeDefNVIC_InitStructure;
NVIC_InitStructure.NVIC_IRQChannel =TIM2_IRQn;//選擇TIM2全局中斷
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority =2;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
  

while(1);
}







//以下是報錯函數
#ifdef USE_FULL_ASSERT
void assert_failed(uint8_t* file,uint32_t line)
{
  while(1)
  {
  }
}
#endif




作者: 哈哈哈哈哈哈11    時間: 2015-8-2 11:25
是這樣子設置的，



歡迎光臨 (http://www.torrancerestoration.com/bbs/) Powered by Discuz! X3.1