国产美女一丝不佳毛片,国产在线愉拍视频

標題: 請教大神：GY-VL53L0X激光模塊ARDUINO源碼串口輸出數據的意義？ [打印本頁]

作者: 13826305429 時間: 2017-4-20 08:56
標題: 請教大神：GY-VL53L0X激光模塊ARDUINO源碼串口輸出數據的意義？
GY-VL53L0X激光模塊

在串口輸出一下數據：
----- START TEST ----
Revision ID: 16
Device ID: 238
PRE_RANGE_CONFIG_VCSEL_PERIOD=7
decode: 16
FINAL_RANGE_CONFIG_VCSEL_PERIOD=5
decode: 12
ready
ambient count: 30
signal count: 569
distance 1800
status: 11
----- END TEST ----

其中distance 指的應該是距離，請教各位大神：其它量“ambient coun”、“signal count”、“status”、” decode“指的是什么？

附Arduino源碼：
//the original code by Ted Meyers
//posted here: https://groups.google.com/d/msg/ ... ZYuJOg/ICPrYNJGBgAJ

#include <Wire.h>

#define VL53L0X_REG_IDENTIFICATION_MODEL_ID       0xc0
#define VL53L0X_REG_IDENTIFICATION_REVISION_ID    0xc2
#define VL53L0X_REG_PRE_RANGE_CONFIG_VCSEL_PERIOD 0x50
#define VL53L0X_REG_FINAL_RANGE_CONFIG_VCSEL_PERIOD 0x70
#define VL53L0X_REG_SYSRANGE_START                0x00
#define VL53L0X_REG_RESULT_INTERRUPT_STATUS       0x13
#define VL53L0X_REG_RESULT_RANGE_STATUS          0x14
#define address 0x29

byte gbuf[16];

void setup() {
  // put your setup code here, to run once:
  Wire.begin();       // join i2c bus (address optional for master)
  Serial.begin(9600);  // start serial for output
  Serial.println("VLX53LOX test started.");
}

void loop() {
  Serial.println("----- START TEST ----");
  test();
  Serial.println("----- END TEST ----");
  Serial.println("");
  delay(1000);
}

void test() {
  byte val1 = read_byte_data_at(VL53L0X_REG_IDENTIFICATION_REVISION_ID);
  Serial.print("Revision ID: "); Serial.println(val1);

  val1 = read_byte_data_at(VL53L0X_REG_IDENTIFICATION_MODEL_ID);
  Serial.print("Device ID: "); Serial.println(val1);

  val1 = read_byte_data_at(VL53L0X_REG_PRE_RANGE_CONFIG_VCSEL_PERIOD);
  Serial.print("PRE_RANGE_CONFIG_VCSEL_PERIOD="); Serial.println(val1);
  Serial.print(" decode: "); Serial.println(VL53L0X_decode_vcsel_period(val1));

  val1 = read_byte_data_at(VL53L0X_REG_FINAL_RANGE_CONFIG_VCSEL_PERIOD);
  Serial.print("FINAL_RANGE_CONFIG_VCSEL_PERIOD="); Serial.println(val1);
  Serial.print(" decode: "); Serial.println(VL53L0X_decode_vcsel_period(val1));

  write_byte_data_at(VL53L0X_REG_SYSRANGE_START, 0x01);

  byte val = 0;
  int cnt = 0;
  while (cnt < 100) { // 1 second waiting time max
delay(10);
val = read_byte_data_at(VL53L0X_REG_RESULT_RANGE_STATUS);
if (val & 0x01) break;
cnt++;
  }
  if (val & 0x01) Serial.println("ready"); else Serial.println("not ready");

  read_block_data_at(0x14, 12);
  uint16_t acnt = makeuint16(gbuf[7], gbuf[6]);
  uint16_t scnt = makeuint16(gbuf[9], gbuf[8]);
  uint16_t dist = makeuint16(gbuf[11], gbuf[10]);
  byte DeviceRangeStatusInternal = ((gbuf[0] & 0x78) >> 3);

  Serial.print("ambient count: "); Serial.println(acnt);
  Serial.print("signal count: ");  Serial.println(scnt);
  Serial.print("distance ");    Serial.println(dist);
  Serial.print("status: ");       Serial.println(DeviceRangeStatusInternal);
}

uint16_t bswap(byte b[]) {
  // Big Endian unsigned short to little endian unsigned short
  uint16_t val = ((b[0] << 8) & b[1]);
  return val;
}

uint16_t makeuint16(int lsb, int msb) {
return ((msb & 0xFF) << 8) | (lsb & 0xFF);
}

void write_byte_data(byte data) {
  Wire.beginTransmission(address);
  Wire.write(data);
  Wire.endTransmission();
}

void write_byte_data_at(byte reg, byte data) {
  // write data word at address and register
  Wire.beginTransmission(address);
  Wire.write(reg);
  Wire.write(data);
  Wire.endTransmission();
}

void write_word_data_at(byte reg, uint16_t data) {
  // write data word at address and register
  byte b0 = (data &0xFF);
  byte b1 = ((data >> 8) && 0xFF);

  Wire.beginTransmission(address);
  Wire.write(reg);
  Wire.write(b0);
  Wire.write(b1);
  Wire.endTransmission();
}

byte read_byte_data() {
  Wire.requestFrom(address, 1);
  while (Wire.available() < 1) delay(1);
  byte b = Wire.read();
  return b;
}

byte read_byte_data_at(byte reg) {
  //write_byte_data((byte)0x00);
  write_byte_data(reg);
  Wire.requestFrom(address, 1);
  while (Wire.available() < 1) delay(1);
  byte b = Wire.read();
  return b;
}

uint16_t read_word_data_at(byte reg) {
  write_byte_data(reg);
  Wire.requestFrom(address, 2);
  while (Wire.available() < 2) delay(1);
  gbuf[0] = Wire.read();
  gbuf[1] = Wire.read();
  return bswap(gbuf);
}

void read_block_data_at(byte reg, int sz) {
  int i = 0;
  write_byte_data(reg);
  Wire.requestFrom(address, sz);
  for (i=0; i<sz; i++) {
while (Wire.available() < 1) delay(1);
gbuf = Wire.read();
  }
}

uint16_t VL53L0X_decode_vcsel_period(short vcsel_period_reg) {
  // Converts the encoded VCSEL period register value into the real
  // period in PLL clocks
  uint16_t vcsel_period_pclks = (vcsel_period_reg + 1) << 1;
  return vcsel_period_pclks;

}

作者: 會灰的魚 時間: 2017-6-21 17:26
請問，你的問題得到解決了么？最近也在搞這個，現在我測得的距離不太對，distance在距離近時直接變成20，status也在11和8之間跳。。。。。沒法用啊

作者: guojianpeng5 時間: 2017-7-8 09:20

會灰的魚發表于 2017-6-21 17:26
請問，你的問題得到解決了么？最近也在搞這個，現在我測得的距離不太對，distance在距離近時直接變成20，st ...

您好，我想請教一下，這款傳感器的x和G接口需要接嗎還有是直接用帶的針插進去就可以了么

作者: 9584984k 時間: 2017-10-7 16:44
您好，我也想問一些，這些引腳是怎么連的。我的串口輸出不了這些數據

作者: czl8612120 時間: 2017-11-6 20:48
兄弟，你會濾波嗎 QQ390643675
留下你的聯系方式行嗎

作者: cciew 時間: 2018-3-7 22:29
是這款模塊嗎？注意PS這個針腳，接地是IIC模式，不接地是串口模式！

VL53L0X_IIC.jpg (11.73 KB, 下載次數: 123)

作者: zzhoo7 時間: 2018-4-11 17:40
請問是怎么接線呢

歡迎光臨 (http://www.torrancerestoration.com/bbs/)