找回密碼
 立即注冊

QQ登錄

只需一步，快速開始

搜索
查看: 3720|回復: 1
打印 上一主題 下一主題
收起左側

基于stm32f103c8板子的小車的電機驅動源碼

[復制鏈接]
跳轉到指定樓層
樓主
ID:366692 發表于 2018-7-7 10:36 | 只看該作者 回帖獎勵 |倒序?yàn)g覽 |閱讀模式
這是基于stm32f103c8板子的小車的電機驅動的keil工程源代碼，這里是直流電機，由B6，B7,B8,B9四個管口輸出PWM波來控制，前兩個管口與B電機相關，后兩個與A電機相關，兩個口的PWM波占空比不同，產生壓差，使電機轉動

單片機源程序如下:
  1. #include "PWM.h"
  2. #include "stm32f10x.h"


  5. void TIM4_Init(void)
  6. {
  7.         TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
  8.         GPIO_InitTypeDef GPIO_InitStructure;
  9.         TIM_OCInitTypeDef  TIM_OCInitStructure;
  10.        
  11.         RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOB , ENABLE);
  12.         //GPIO_InitTypeDef GPIO_InitStructure;
  13. //  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6|GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9;
  14. //  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  15. //  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  16. //  GPIO_Init(GPIOB, &GPIO_InitStructure);
  17. //        GPIO_SetBits(GPIOB , GPIO_Pin_6);
  18. //        GPIO_SetBits(GPIOB , GPIO_Pin_7);
  19. //        GPIO_SetBits(GPIOB , GPIO_Pin_8);
  20. //        GPIO_SetBits(GPIOB , GPIO_Pin_9);
  21.        
  22.         GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6;//對應BIN2
  23.   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  24.   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  25.   GPIO_Init(GPIOB, &GPIO_InitStructure);
  26.        
  27.         GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;//對應BIN1
  28.   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  29.   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  30.   GPIO_Init(GPIOB, &GPIO_InitStructure);
  31.        
  32.         GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8;//對應AIN2
  33.   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  34.   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  35.   GPIO_Init(GPIOB, &GPIO_InitStructure);
  36.        
  37.         GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;//對應AIN1
  38.   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  39.   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  40.   GPIO_Init(GPIOB, &GPIO_InitStructure);
  41.                  
  42.   RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4 , ENABLE);
  43.         //TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
  44.   TIM_TimeBaseStructure.TIM_Prescaler = 0;   
  45.         TIM_TimeBaseStructure.TIM_Period = 5000 ;
  46.   TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1 ;//TIM_CKD_DIV1;          
  47.   TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
  48.   TIM_TimeBaseInit(TIM4, &TIM_TimeBaseStructure);

  50.         //TIM_OCInitTypeDef  TIM_OCInitStructure;
  51.         TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;        
  52.   TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  53.         TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable;
  54.   TIM_OCInitStructure.TIM_Pulse =  2500;     
  55.   TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;
  56.   TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCNPolarity_High;
  57.   TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;
  58.   TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCIdleState_Reset;       
  59.   TIM_OC1Init(TIM4 , &TIM_OCInitStructure);
  60.   TIM_OC1PreloadConfig(TIM4 , TIM_OCPreload_Enable);
  61.   TIM_ARRPreloadConfig(TIM4 , ENABLE);   
  62.         TIM_CtrlPWMOutputs(TIM4 , ENABLE);
  63.         TIM_Cmd(TIM4 , ENABLE);       
  64.        
  65.         TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;        
  66.   TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  67.         TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable;
  68.   TIM_OCInitStructure.TIM_Pulse =  0;     
  69.   TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;
  70.   TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCNPolarity_High;
  71.   TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;
  72.   TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCIdleState_Reset;       
  73.   TIM_OC2Init(TIM4 , &TIM_OCInitStructure);
  74.   TIM_OC2PreloadConfig(TIM4 , TIM_OCPreload_Enable);
  75.   TIM_ARRPreloadConfig(TIM4 , ENABLE);   
  76.         TIM_CtrlPWMOutputs(TIM4 , ENABLE);
  77.         TIM_Cmd(TIM4 , ENABLE);       
  78.        
  79.         TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;        
  80.   TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  81.         TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable;
  82.   TIM_OCInitStructure.TIM_Pulse =  2500;     
  83.   TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;
  84.   TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCNPolarity_High;
  85.   TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;
  86.   TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCIdleState_Reset;       
  87.   TIM_OC3Init(TIM4 , &TIM_OCInitStructure);
  88.   TIM_OC3PreloadConfig(TIM4 , TIM_OCPreload_Enable);
  89.   TIM_ARRPreloadConfig(TIM4 , ENABLE);   
  90.         TIM_CtrlPWMOutputs(TIM4 , ENABLE);
  91.         TIM_Cmd(TIM4 , ENABLE);       
  92.        
  93.         TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;        
  94.   TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  95.         TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable;
  96.   TIM_OCInitStructure.TIM_Pulse =  0;     
  97.   TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;
  98.   TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCNPolarity_High;
  99.   TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;
  100.   TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCIdleState_Reset;       
  101.   TIM_OC4Init(TIM4 , &TIM_OCInitStructure);
  102.   TIM_OC4PreloadConfig(TIM4 , TIM_OCPreload_Enable);
  103.   TIM_ARRPreloadConfig(TIM4 , ENABLE);   
  104.         TIM_CtrlPWMOutputs(TIM4 , ENABLE);
  105.         TIM_Cmd(TIM4 , ENABLE);       
  106.         //TIM1->CCR1 = 200;
  107.        
  108. }

復制代碼

所有資料51hei提供下載:
驅動電機.rar (390.61 KB, 下載次數: 36)



分享到:  QQ好友和群QQ好友和群 QQ空間QQ空間 騰訊微博騰訊微博 騰訊朋友騰訊朋友
收藏收藏 分享淘帖 頂頂 踩踩
回復

使用道具 舉報

沙發
ID:394828 發表于 2018-9-8 10:24 | 只看該作者
很不錯
回復

使用道具 舉報

您需要登錄后才可以回帖 登錄 | 立即注冊

本版積分規則

手機版|小黑屋|51黑電子論壇 |51黑電子論壇6群 QQ 管理員QQ:125739409;技術交流QQ群281945664

Powered by 單片機教程網

快速回復 返回頂部 返回列表