本帖最后由 venom6 于 2019-8-10 14:25 編輯
車是一款獨創的基于STC15W4K61S4單片機的全地形物聯網運輸車。它的機械結構部分參照了2011年的好奇號火星探測器，為了適應城市中的樓梯、臺階等地形又將它的機械結構做了調整。作品電路包括藍牙模塊、遠程圖傳模塊、MP3模塊、矩陣按鍵密碼箱、GPS模塊以及基本的供電、運動模塊，所有功能均可用單個上位機遠程操控。其主要功能是實現快遞、外賣的短途運輸，且該過程均可由操作者遠程實現，此外作品還可以應用于復雜地形的探險、救援、物資運輸?shù)阮I(lǐng)域。如有朋友想詳細了解車的結構和單片機程序，可以評論下。本人很菜，希望與大家交流。 ******************************************************************************/
#include "main.h"
#include "delay.h"
#include "uart.h"
#define uchar unsigned char
#define uint unsigned int
#define KEY P1
uchar k;
uint a=0;
uchar code table[]={0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08, 0x09, 0x00};
uchar code key_code[]={0x77, 0xb7, 0xd7, 0x7b, 0xbb, 0xdb, 0x7d, 0xbd, 0xdd, 0xbe};
uchar code pass_word[3]={1,2,3};
uint mima[3]={0,0,0};
******************************************/ /
void GPIO_config(void)
{
P0M1 = 0; P0M0 = 0;
P1M1 = 0; P1M0 = 0;
P2M0 = 0; P2M1 = 0;
P3M1 = 0; P3M0 = 0;
P4M1 = 0; P4M0 = 0;
P5M0 = 0;
P5M1 = 0;
} /*****************************************/
void main(void)
{
KEY=0xff;
GPIO_config();
UartInit();
Uart2SendString("Please enter your command:\r\n");
delay_ms(200);
while(1)
{ if(Hand("MP3"))
{
LED = LED_ON;
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1501T0000!");
Uart2SendString("#001P1501T0000!");
}
if(Hand("Z"))
{
LED = LED_ON;
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1511T0000!");
Uart2SendString("#001P1511T0000!");
}
if(Hand("S"))
{
LED = LED_OFF;
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1499T0000!");
Uart2SendString("#001P1499T0000!");
}
if(Hand("NEXT"))
{
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1496T0000!");
Uart2SendString("#001P1496T0000!");
}
if(Hand("#001P1495T0000!"))
{
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1495T0000!");
Uart2SendString("#001P1495T0000!");
}
if(Hand("UP"))
{
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1494T0000!");
Uart2SendString("#001P1494T0000!");
}
if(Hand("#001P1493T0000!"))
{
CLR_Buf();
Uart2CLR_Buf();
SendString("#001P1493T0000!");
Uart2SendString("#001P1493T0000!");
}
else if(Hand("GO"))
{
IN1 =1;
IN2 =0;
IN3 =0;
IN4 =1;
CLR_Buf();
SendString("#Command: GO, Executed!\r\n");
}
else if(Hand("BAC"))
{
IN1 =0;
IN2 =1;
IN3 =1;
IN4 =0;
CLR_Buf();
SendString("#Command: BACK, Executed!\r\n");
}
else if(Hand("LEFT"))
{
IN1 =1;
IN2 =0;
IN3 =1;
IN4 =0;
CLR_Buf();
SendString("#Command: LEFT, Executed!\r\n");
}
else if(Hand("RIGHT"))
{
IN1 =0;
IN2 =1;
IN3 =0;
IN4 =1;
CLR_Buf();
SendString("#Command: RIGHT, Executed!\r\n");
}
else if(Hand("TING"))
{
IN1 =0;
IN2 =0;
IN3 =0;
IN4 =0;
MIMASUO =1;
BEEP=1;
CLR_Buf();
SendString("#Command: TING, Executed!\r\n");
}
else if(Hand("K"))
{
MIMASUO =0;
BEEP=0;
CLR_Buf();
Uart2CLR_Buf();
SendString("#Command: KAISUO, Executed!\r\n");
Uart2SendString("#001P1513T0000!");
}
else if(Uart2Hand("ledoff"))
{
LED = LED_OFF;
Uart2CLR_Buf();
Uart2SendString("LED Off!\r\n");
}
}
}
| 
QQ好友和群
QQ空間
騰訊微博
騰訊朋友
收藏
淘帖
頂
踩
