|
|
今天在調試串口程序時發現（STM32107RC），UART4明明就是配置好了，可以發送，但是就是不能中斷接受。在網上看到很多人也有這個疑問，今晚終于搞定，順便寫篇博客，希望能幫到下一個遇到同樣問題的人。最主要的問題是啟動代碼有問題，不知道我那啟動代碼是什么年代的了，所以沒有添加UART4，UART5.
如果你出現了這個問題，去看看啟動代碼是否有
IMPORT UART4_IRQHandler
IMPORT UART5_IRQHandler
DCD UART4_IRQHandler
DCD UART5_IRQHandler
如果有的話，還不行，那我也不清楚了。另尋他人！
沒有的話去找個新的啟動引導程序。
順便也把我初始化配置貼出來，大家也好比較！這樣的初始化我是可以運行！
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC,ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_UART4, ENABLE);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
GPIO_Init(GPIOC, &GPIO_InitStructure);
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength =USART_WordLength_8b;
USART_InitStructure.USART_StopBits =USART_StopBits_1;
USART_InitStructure.USART_Parity =USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl =USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx |USART_Mode_Tx;
USART_Init(UART4, &USART_InitStructure);
USART_ITConfig(UART4, USART_IT_RXNE, ENABLE);
USART_Cmd(UART4, ENABLE);
NVIC_InitStructure.NVIC_IRQChannel =UART4_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority =1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
void UART4_IRQHandler(void)
{能進入中斷就行}
Send_String("ABC",3);//發送函數
void Send_String(char *buff,INT16U Len)
{
INT16U i;
for(i=0;i
{
USART_SendData(UART4,*buff++);
while(USART_GetFlagStatus(UART4, USART_FLAG_TXE) ==RESET);
}
}
|
|
