基于STM32F103兩輪平衡小車設計（開源）

ID:127084 · 發表于 2016-6-17 14:25

給大家分享個兩輪平衡小車設計，不多說了，直接上圖

附件資料

/**---------------------------------------------------------------
項目：兩輪自平衡小車(Two-Wheels Auto-Balancing Vechile)
版本：v1.0.0
文件：AHRS_Rcv.c
功能：AHRS姿態數據接收
作者：[email]flotox@yeah.net[/email]
日期：2014.9.7
更新：2014.9.7
----------------------------------------------------------------*/
#include "stm32f10x.h"
#include "AHRS_Rcv.h"
/**
* @brief AHRS姿態數據接收外設初始化
* @param none
* @retval none
*/
void AHRS_Rcv_Init(void){
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
/*開啟GPIOC外設時鐘*/
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
/*開啟USART2外設時鐘*/
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);
/*USART2的GPIO配置*/
/*配置USART2 Tx(PA.02)為AF_PP模式*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/*配置USART2 Rx(PA.03)為IN_FLOATING*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/*USART2 NVIC配置*/
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //2 bits for pre-emption priority 2 bits for subpriority
NVIC_InitStructure.NVIC_IRQChannel = USART2_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; //指定搶占式優先級別,可取0~3
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //指定響應式優先級別,可取0~3
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
/*USART2模式配置*/
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART2, &USART_InitStructure);
USART_Cmd(USART2, ENABLE);
/*接收中斷使能*/
USART_ITConfig(USART2, USART_IT_RXNE, ENABLE);
}